table of contents
other versions
- wheezy 20120510dfsg0-1
foo2xqx(1) | General Commands Manual | foo2xqx(1) |
rr_n {.nr rr_n 0 1 foo2xqx - Convert Ghostscript pbmraw
into a XQX printer stream foo2xqx [options]
<pbmraw-file >xqx-file foo2xqx converts Ghostscript
pbmraw to monochrome XQX streams, for driving the HP LaserJet
P1005/P1006/P1007/P1008, the HP LaserJet P1505, the HP LaserJet P2014, the HP
LaserJet M1005 MFP, the HP LaserJet M1120 MFP, and other XQX-based printers.
These are the options used to select the parameters of a print job that are
usually controlled on a per job basis.
/usr/bin/foo2xqx foo2xqx-wrapper(1), xqxdecode(1) Rick
Richardson <rick.richardson@comcast.net>
http://foo2xqx.rkkda.com/
- -d duplex
- Duplex code to send to printer [1].
1 off 2 long edge 3 short edge
- -g xpixxypix
- Set page dimensions in pixels [10200x6600].
- -m media
- Media code to send to printer [1].
Media M1005 standard 1 transparency 2 envelope 257 letterhead 259 thick 261 postcard 262 labels 263
- -p paper
- Paper code to send to printer [1].
1 letter 9 A4 5 legal 11 A5 7 executive 13 B5 20 env #10 27 env DL 28 env C5 34 env B5 37 env Monarch 257 16k 197x273 263 16k 184x260 264 16k 195x270
- -n copies
- Number of copies [1].
- -r xresxyres
- Set device resolution in pixels/inch [1200x600].
- -s source
- Source (InputSlot) code to send to printer [7].
1 upper 4 manual 2 lower 7 auto
- -t
- Draft mode. Every other pixel is white.
- -T density
- Print density (1-5). The default is 3 (medium).
- -J filename
- Filename string to send to printer.
- -U username
- Username string to send to printer. These are the options used to customize the operation of foo2xqx for a particular printer.
- -u xoffxyoff
- Set the offset of the start of the printable region from the upper left corner, in pixels [0x0].
- -l xoffxyoff
- Set the offset of the end of the printable region from the lower right corner, in pixels [0x0].
- -L mask
- Send logical clipping amounts implied by -u/-l in the
ZjStream [3].
0 don't send any logical clipping amounts 1 only send Y clipping amount 2 only send X clipping amount 3 send both X and Y clipping amounts
- -A
- AllIsBlack: convert C=1,M=1,Y=1 to just K=1. Works with bitcmyk input only.
- -B
- BlackClears: K=1 forces C,M,Y to 0. Works with bitcmyk input only. These options are used for debugging foo2xqx.
- -S plane
- Output just a single color plane from a color print and
print it on the black plane. The default is to output all color planes.
1 Cyan 2 Magenta 3 Yellow 4 Black
- -D level
- Set Debug level [0].
gs -q -dBATCH -dSAFER -dQUIET -dNOPAUSE -sPAPERSIZE=letter -r1200x600 -sDEVICE=pbmraw -sOutputFile=- - < testpage.ps | foo2xqx -r1200x600 -g10200x6600 -p1 >testpage.zm
Wed May 23 16:07:49 2012 | foo2xqx 0.0 |