NAME¶
wvdial.conf - wvdial configuration file
DESCRIPTION¶
When
wvdial starts, it first loads its configuration from
/etc/wvdial.conf, which contains basic information about the modem
port, speed, and init string, along with information about your Internet
Service Provider (ISP), such as the phone number, your username, and your
password.
The configuration file
/etc/wvdial.conf is in Windows "ini"
file format, with
sections named in square brackets and a number of
variable = value pairs within each section.
Here is a sample configuration file:
[Dialer Defaults]
Modem = /dev/ttyS2
Baud = 57600
Init = ATZ
Init2 = AT S11=50
Phone = 555-4242
Username = apenwarr
Password = my-password
[Dialer phone2]
Phone = 555-4243
[Dialer shh]
Init3 = ATM0
[Dialer pulse]
Dial Command = ATDP
The sample configuration file above contains all of the options necessary to run
the two sample command lines given above. Here is a complete list of settings
that
wvdial understands:
- Modem
- The location of the device that wvdial should use as
your modem. The default is /dev/modem.
- Baud
- The speed at which wvdial will communicate with your
modem. The default is 57600 baud.
- Init1 ... Init9
- wvdial can use up to nine initialization strings to
set up your modem. Before dialing, these strings are sent to the modem in
numerical order. These are particularly useful when specifying multiple
sections. See above for an example that uses Init3 to turn the modem's
speaker off. The default is "ATZ" for Init1.
- Phone
- The phone number you want wvdial to dial. You can
add up to 4 other phone numbers that wvdial will dial in order, by
adding:
- Phone1
- Phone2
- Phone3
- Phone4
- Dial Prefix
- wvdial will insert this string after the dial
command and before the phone number. For example, to disable call waiting
(in North America, anyway) set this to "*70,".
- Dial Command
- wvdial will use this string to tell the modem to
dial. The default is "ATDT".
- Login
- You must set this to the username you use at your ISP.
- Login Prompt
- If your ISP has an unusual login procedure that
wvdial is unable to figure out, you can use this option to specify
a login prompt. When this prompt is received from your ISP, wvdial
will send the Login string.
- Password
- You must set this to the password you use at your ISP.
- Ask Password
- By setting this option wvdial will prompt for your
password on every dialin. Thus you don't have to save your password in
/etc/wvdial.conf. (Option added by SuSE.)
- Password Prompt
- If your ISP has an unusual login procedure that
wvdial is unable to figure out, you can use this option to specify
a password prompt. When this prompt is received from you ISP,
wvdial will send the Password string.
- PPPD Path
- If your system has pppd somewhere other than
/usr/sbin/pppd, you will need to set this option.
- Auto DNS
- Try to get the Domain Nameserver (DNS) from the provider.
This option is "on" by default. (Option added by SuSE.)
- Check DNS
- Check the Domain Nameserver (DNS) after the connection has
been set up. This option is "on" by default. (Option added by
SuSE.)
- DNS Test1
- First DNS lookup for DNS check. (Option added by
SuSE.)
- DNS Test2
- Second DNS lookup for DNS check. (Option added by
SuSE.)
- Check Def Route
- Check the default route after the connection has been set
up. This option is "on" by default. (Option added by SuSE.)
- Force Address
- This option only applies if you have a static IP address at
your ISP, and even then you probably don't need it. Some ISP's don't send
the IP address as part of the PPP negotiation. This option forces pppd to
use the address you give it.
- Remote Name
- If your ISP uses PAP or CHAP authentication, you might need
to change this to your ISP's authentication name. In most cases, however,
it's safe to use the default value, "*".
- Carrier Check
- wvdial checks your modem during the connection
process to ensure that it is actually online. If you have a weird modem
that insists its carrier line is always down, you can disable the carrier
check by setting this option to "no".
- Stupid Mode
- When wvdial is in Stupid Mode, it does not attempt
to interpret any prompts from the terminal server. It starts pppd
immediately after the modem connects. Apparently there are ISP's that
actually give you a login prompt, but work only if you start PPP, rather
than logging in. Go figure. Stupid Mode is (naturally) disabled by
default.
- New PPPD
- You need this option if you have pppd version 2.3.0 or
newer, to make wvdial create the file /etc/ppp/peers/wvdial. This
option is enabled by default, thus if you have older pppd you need to set
it to `no' (or upgrade pppd).
- Default Reply
- When wvdial detects a prompt, and it hasn't seen any
clues that indicate what it should send as a response to the prompt, it
defaults to sending "ppp". Sometimes this is inadequate. Use
this option to override wvdial's default prompt response.
- Auto Reconnect
- If enabled, wvdial will attempt to automatically
reestablish a connection if you are randomly disconnected by the other
side. This option is "on" by default.
- Idle Seconds
- Set the hangup timeout in seconds. If there is inactivity
for the given time the connection is shut down. A hangup timeout of 0
disables this feature.
- Abort on Busy
- If enabled, wvdial will not retry the connection if
the modem says that the line is busy. This option is "off" by
default.
- Abort on No Dialtone
- If enabled, wvdial will not retry the connection if
the modem says that there is no dialtone. This option is "on" by
default.
- Dial Attempts
- If value is set, wvdial will quit after that many
tries .If set to 0, wvdial will happily keep dialling forever.
- Dial Timeout
- The maximum time in seconds that wvdial will wait
for a connection to be made. Default value is 60 seconds.
The
wvdialconf(1) program can be used to detect your modem and fill in
the Modem, Baud, and Init/Init2 options automatically.
AUTHORS¶
Dave Coombs and Avery Pennarun for Net Integration Technologies Inc. Great
contributions have been made by many people, including SuSE and RedHat. Thanks
guys!
SEE ALSO¶
wvdial(1),
wvdialconf(1),
pppd(8).