include section¶

Include other configuration files. Each line in this section, enclosed in quotation marks ("), must be a valid filename or a valid file globbing pattern (it is ok, if no files match this pattern). The contents of this file / these files are added to the actual configuration and each file should contain at least one section (a comment only file is not really useful...).

include4 section¶

Include other configuration files but ONLY in IPv4 mode (WITHOUT -6 switch to uif). Otherwise equivalent to the include section above.

include6 section¶

Include other configuration files but ONLY in IPv6 mode (WITH -6 switch to uif). Otherwise equivalent to the include section above.

sysconfig section¶

Set some global settings. Each line in this section starts with one of the following identifiers followed by one or more blanks and the desired value: LogLevel, LogPrefix, LogLimit, LogBurst, Limit, Burst or AccountPrefix. If there are multiple definitions of one entry the last definition is stored.

LogLevel

A valid default log priority (see syslog.conf(5)).

LogPrefix

The default log prefix. Each netfilter (or iptables) log message starts with this prefix.

LogLimit

The default limit value for log messages (see nft(8) or iptables(8)).

LogBurst

The default burst value for log messages (see nft(8) or iptables(8)).

Limit

The default limit value (see nft(8) or iptables(8)).

Burst

The default burst value (see nft(8) or iptables(8)).

AccountPrefix

The default prefix for accounting chains.

service section¶

This section defines all needed services. A service description starts with the protocol (see protocols(5)) followed by parameters in parenthesis. Most protocols don't need any parameters. The only exceptions are tcp, udp and icmp. The tcp and udp parameters define the source and destionation port(-range). The source and destination ports are separated by a slash (/) and port ranges are separated by a colon (eg. tcp(123:333/99): tcp protocol, source port range 123-333, destination port 99). Empty source or destination ports are expanded to 1:65535. The icmp protocol parameter must be a valid icmp type (see iptables -p icmp --help).

network section¶

This section defines all needed networks and hosts. A network description starts with a valid IPv4 address (dotted quad), a valid IPv6 address (colon syntax, square brackets not needed), an optional netmask in cidr notation (number of bits) or an optional MAC-address (with a prefixed equal sign (=). Some valid entries are: 127.0.0.1, 127.0.0.0/8, ::1, fd00:1:2:3::/64,
and 192.168.0.1=00:00:00:00:00:FF.

interface section¶

This section defines all needed (physical and bridged) interfaces (eg. eth0, lo, ppp0).

marker section¶

This section defines all needed numerical (decimal) values for packet marking purposes.

filter, nat, input, output, forward, masquerade and stateless sections¶

Due to better partitioning of the packetfilter, rules can be split into these sections. Internally they are equivalent and contain all rules. As an exception to all other sections the order of entries in these sections is important.

The default policy for the chains INPUT, OUTPUT and FORWARD is DROP (see nft(8) or iptables(8)) and it's not possible to change this.

Each line in in this section begins with in, out, fw, nat, masq, slin, slout or slfw, followed by '+', '-' or a mark identifier enclosed in curly braces (or, in case of fw followed by '>'). The identifiers in, out and fw define rules for incoming, outgoing and forwarded IP-packets. Each packet with an INVALID state (see nft(8) or iptables(8)) is matched by slin, slout and slfw. The lines starting with nat and masq define rules to modify the source or destination address or the destination port.

Note: The identifiers nat and masq are non-operational in IPv6 mode. They simply get ignored as NAT and Masquerading are not supported by the IPv6 protocol.

The plus and minus signs specify the type of the rule: '+' accepts matching packets and '-' drops them. As a special case the identifier out and fw accept the greater than (>) sign to modify the MSS depending on the PMTU (see iptables(8)).

A very basic ruleset may look like this: out+

This allows every outgoing traffic and rejects all incoming connections (because of the default policy).

To be more specific, each line may contain several parameters. Each parameter starts with a single character followed by an equal sign (=) and one or more previously defined identifiers (in the corresponding sections) separated by commas. The following parameters are valid:

s

The source address or network. Append "(4)" or "(6)" to the network name to make this rule apply to IPv4 or IPv6 only.

d

The destination address or network. Append "(4)" or "(6)" to the network name to make this rule apply to IPv4 or IPv6 only.

i

The input interface.

o

The output interface.

pi

The physical input interface (only useful when used with bridged interfaces, not supported with nft as deprecated there).

po

The physical output interface (only useful when used with bridged interfaces, not supported with nft as deprecated there).

p

The service description (protocol).

m

The mark field associated with a packet.

S

The the new source address in nat rules. Supported in IPv4 mode only. Ignored in IPv6 mode.

D

The the new destination address in nat rules. Supported in IPv4 mode only. Ignored in IPv6 mode.

P

The the new service description in nat rules. This is only valid with tcp or udp packets.

f

This parameter sets some 'flags'. A flag definition starts with the flag identifier and optional parameters in parenthesis. Valid flags are:

log - Logs matching packages to syslog. The given parameter is included in the log entry. The number of logged packets and the loglevel can be set in the sysconfig section.

reject - Only valid in DROP rules. This is used to send back an error packet in response to the matched packet. The default behaviour is a packet with set RST flag on tcp connections and a destination-unreachable icmp packet in every other case. Valid parameters are listed in iptables(8) in the REJECT section.

account - Create an accounting chain for all matching packages and possible responses. The optional parameter is a part of the name of the chain.

limit - Limits the number of matching packets. The default values are set in the sysconfig section. Other values can be defined with the optional parameter. The first entry sets a new limit and the second parameter (separated by a comma (,)) sets the burst value (see Limit and Burst in sysconfig section).

It's possible to invert the identifier of one of following parameters - if it expands to ecactly one object - by prepending a exclamation mark (!): s, d, i, o, p (eg.: s=!local p=!http).