# This is a tunnel instance named "t1"
[tunnel.t1]
# peer specifies the address of the peer that the tunnel should
# connect its socket to
peer = "127.0.0.1:5001"
# version specifies the version of the L2TP specification the
# tunnel should use.
# Currently supported values are "l2tpv2".
version = "l2tpv2"
# encap specifies the encapsulation to be used for the tunnel.
# L2TPv2 tunnels are UDP only.
encap = "udp"
# local specifies the local address that the tunnel should
# bind its socket to
local = "127.0.0.1:5000"
# tid specifies the local tunnel ID of the tunnel.
# Tunnel IDs must be unique for the host.
# L2TPv2 tunnel IDs are 16 bit, and may be in the range 1 - 65535.
# L2TPv3 tunnel IDs are 32 bit, and may be in the range 1 - 4294967295.
tid = 62719
# ptid specifies the peer's tunnel ID for the tunnel.
# The peer's tunnel ID must be unique for the peer, and are unrelated
# to the local tunnel ID.
# The rules for tunnel ID range apply to the peer tunnel ID too.
ptid = 72819
# window_size specifies the initial window size to use for the L2TP
# reliable transport algorithm which is used for control protocol
# messages.  The window size dictates how many control messages the
# tunnel may have "in flight" (i.e. pending an ACK from the peer) at
# any one time.  Tuning the window size can allow high-volume L2TP servers
# to improve performance.  Generally it won't be necessary to change
# this from the default value of 4.
window_size = 10 # control messages
# hello_timeout if set enables L2TP keep-alive (HELLO) messages.
# A hello message is sent N milliseconds after the last control
# message was sent or received.  It allows for early detection of
# tunnel failure on quiet connections.
# By default no keep-alive messages are sent.
hello_timeout = 7500 # milliseconds
# retry_timeout if set tweaks the starting retry timeout for the
# reliable transport algorithm used for L2TP control messages.
# The algorithm uses an exponential backoff when retrying messages.
# By default a starting retry timeout of 1000ms is used.
retry_timeout = 1500 # milliseconds
# max_retries sets how many times a given control message may be
# retried before the transport considers the message transmission to
# have failed.
# It may be useful to tune this value on unreliable network connections
# to avoid suprious tunnel failure, or conversely to allow for quicker
# tunnel failure detection on reliable links.
# The default is 3 retries.
max_retries 5
# host_name sets the host name the tunnel will advertise in the
# Host Name AVP per RFC2661.
# If unset the host's name will be queried and the returned value used.
host_name "basilbrush.local"
# framing_caps sets the framing capabilities the tunnel will advertise
# in the Framing Capabilities AVP per RFC2661.
# The default is to advertise both sync and async framing.
framing_caps = ["sync","async"]
    

# This is a session instance called "s1" within parent tunnel "t1".
# Session instances are always created inside a parent tunnel.
[tunnel.t1.session.s1]
# pseudowire specifies the type of layer 2 frames carried by the session.
# Currently supported values are "ppp", "eth", and "pppac".
# L2TPv2 tunnels support PPP and PPPAC pseudowires only.
pseudowire = "eth"
# pppd_args specifes a file to be read for pppd arguments.  These should
# be either whitespace or newline delimited, and should call out pppd command
# line arguments as described in the pppd manpage.
pppd_args = "/etc/kl2tpd/t1s1_pppd_args.txt"
# sid specifies the local session ID of the session.
# Session IDs must be unique to the tunnel for L2TPv2, or unique to
# the peer for L2TPv3.
# L2TPv2 session IDs are 16 bit, and may be in the range 1 - 65535.
# L2TPv3 session IDs are 32 bit, and may be in the range 1 - 4294967295.
sid = 12389
# psid specifies the peer's session ID for the session.
# The peer's session ID is unrelated to the local session ID.
# The rules for the session ID range apply to the peer session ID too.
psid = 1234
# seqnum, if set, enables the transmission of sequence numbers with
# L2TP data messages.  Use of sequence numbers enables the data plane
# to reorder data packets to ensure they are delivered in sequence.
# By default sequence numbers are not used.
seqnum = false
# pppoe_session_id specifies the assigned PPPoE session ID for the session.
# Per RFC2516, the PPPoE session ID is in the range 1 - 65535
# This parameter only applies to pppac pseudowires.
pppoe_session_id = 1234
# pppoe_peer_mac specifies the MAC address of the PPPoE peer for the session.
# This parameter only applies to pppac pseudowires.
pppoe_peer_mac = [ 0x02, 0x42, 0x94, 0xd1, 0x4e, 0x9a ]