| NWIPE(1) | User Commands | NWIPE(1) |
NAME¶
nwipe - securely erase disks
SYNOPSIS¶
nwipe [options] [device1] [device2] ...
DESCRIPTION¶
nwipe is a command that will securely erase disks using a variety of recognised methods. It is a fork of the dwipe command used by Darik's Boot and Nuke (dban). nwipe is included with partedmagic if you want a quick and easy bootable CD version. nwipe was created out of a need to run the DBAN dwipe command outside of DBAN, in order to allow its use with any host distribution, thus giving better hardware support. It is essentially the same as dwipe, with a few changes:
OPTIONS¶
- -V, --version
- Prints the version number
- -h, --help
- Prints a help summary
- --autonuke
- If no devices have been specified on the command line, starts wiping all devices immediately. If devices have been specified, starts wiping only those specified devices immediately.
- --autopoweroff
- Power off system on completion of wipe delayed for for one minute. During this one minute delay you can abort the shutdown by typing sudo shutdown -c
- --sync=NUM
- Will perform a syn after NUM writes (default: 100000)
- 0 - fdatasync after the disk is completely written
fdatasync errors not detected until completion.
0 is not recommended as disk errors may cause nwipe
to appear to hang - 1 - fdatasync after every write
Warning: Lower values will reduce wipe speeds. - 1000 - fdatasync after 1000 writes
- --noblank
- Do not perform the final blanking pass after the wipe (default is to blank, except when the method is RCMP TSSIT OPS-II).
- --nowait
- Do not wait for a key before exiting (default is to wait).
- --nosignals
- Do not allow signals to interrupt a wipe (default is to allow).
- --nousb
- Do not show or wipe any USB devices, whether in GUI, --nogui or autonuke mode. (default is to allow USB devices to be shown and wiped).
- --nogui
- Do not show the GUI interface. Can only be used with the autonuke option. Nowait option is automatically invoked with the nogui option. SIGUSR1 can be used to retrieve the current wiping statistics.
- -v, --verbose
- Log more messages, useful for debugging.
- --verify=TYPE
- Whether to perform verification of erasure (default: last)
- off - Do not verify
- last - Verify after the last pass
- all - Verify every pass
- Please mind that HMG IS5 enhanced always verifies the last (PRNG) pass regardless of this option.
- -m, --method=METHOD
- The wiping method (default: dodshort).
- dod522022m / dod - 7 pass DOD 5220.22-M method
- dodshort / dod3pass - 3 pass DOD method
- gutmann - Peter Gutmann's Algorithm
- ops2 - RCMP TSSIT OPS-II
- random / prng / stream - PRNG Stream
- zero / quick - Overwrite with zeros 0x00
- one - Overwrite with ones 0xFF
- verify_zero - Verifies disk is zero filled
- verify_one - Verifies disk is 0xFF filled
- is5enh - HMG IS5 enhanced
- -l, --logfile=FILE
- Filename to log to. Default is STDOUT
- -p, --prng=METHOD
- PRNG option (mersenne|twister|isaac|isaac64)
- -q, --quiet
- Anonymize serial numbers, Gui & logs display:
XXXXXXXX = S/N obtained & anonymized.
???????? = S/N not available. - -r, --rounds=NUM
- Number of times to wipe the device using the selected method (default: 1)
- -e, --exclude=DEVICES
- Up to ten comma separated devices to be excluded, examples:
--exclude=/dev/sdc
--exclude=/dev/sdc,/dev/sdd
BUGS¶
Please see the GitHub site for the latest list (https://github.com/martijnvanbrummelen/nwipe/issues)
AUTHOR¶
Nwipe is developed by Martijn van Brummelen <github@brumit.nl>
SEE ALSO¶
| March 2022 | nwipe version 0.33 |