table of contents
|Pamlevels User Manual(1)||General Commands Manual||Pamlevels User Manual(1)|
pamlevels - effect a 'levels' transformation
pamlevels -from1 from1 -to1 to1 -from2 from2 -to2 to2 [-from3 from3 -to3 to3] [-linear] [-fitbrightness] [pamfile]
This program is part of Netpbm(1).
pamlevels reads a Netpbm image from pamfile or standard input, applies a 'levels' transformation, and sends the result to standard output. It finds a unique transformation that maps color from1 to to1, color from2 to to2, and-if -from3 and -to3 are supplied-color from3 to to3. Transformations based on two mappings are linear in light intensity and those based on three mappings quadratic. The color-mapping options may be shortened to -f1...-f3 and -t1...-t3.
Color values have the following format:
color[:scale], where color is a
Netpbm color specification and scale an optional coefficient that is applied to the intensity (i.e. not gamma-adjusted) of each RGB component of color.
When the transformation is linear (i.e. uses two mappings) and preserves zero (i.e. maps black to black), it corresponds to multiplication of light intensity by a constant and preserves color integrity(1).
In the examples below, \ denotes a line continuation:
To brighten an image by setting a darker white point-
pamlevels -f1 black -t1 black \
-f2 white:0.9 -t2 white in.ppm > out.ppm
To adjust the white point-
pamlevels -f1 black -t1 black \
-f2 rgbi:0.9/0.83/0.80 -t2 white in.ppm > out.ppm
To set a lighter black point-
pamlevels -f1 white:0.06 -t1 black \
-f2 white -t2 white in.ppm > out.ppm
To increase brightness by compression-
The latter tranformation is similar to gamma-correction.
-f1 black -t1 black -f2 white -t2 white \
-f3 white:0.5 -t3 white:0.6 in.ppm > out.ppm
In addition to the options common to all programs based on
libnetpbm (most notably -quiet, see
Common Options ), pamlevels recognizes the following command line options:
- These options define the mappings of input colors to output colors that
anchor the transformation function. See
You must specify at least two of these pairs.
- This option tells pamlevels to work with the intensity-linear
variation on PPM where the samples are proportional to light intensity,
rather than brightness (gamma-adjusted) as in true PPM. The input must be
of this form and the pamlevels makes the output of this form.
Note that the numbers in a color specification like rgbi:0.9/0.83/0.80 are brightness levels (gamma-adjusted) regardless of the input and output format.
You cannot use this with -fitbrightness because that function is not implemented.
- This option selects a transformation which is not very useful - it is
linear or quadratic in brightness rather than light intensity of the
pixels. There is no physical basis for doing it this way and the result is
Note that many tools other than Netpbm do the transformation this way. One use for this option is simply to demonstrate the poor result of this method.
One advantage of this transformation is that it is faster, because the input and output image formats use brightness values. The result is approximately correct.
You cannot use this with -linear because that function is not implemented.
pnmnorm(1), pamrecolor(1), pnmgamma(1), pnm(1)
This program was first submitted by Anton Shepelev (firstname.lastname@example.org).
pamlevels was new in Netpbm 10.83 (June 2018).
This manual page was generated by the Netpbm tool 'makeman' from HTML source. The master documentation is at
|13 June 2018||netpbm documentation|