table of contents
XOSVIEW(1) | General Commands Manual | XOSVIEW(1) |
NAME¶
xosview - X based system monitorSYNOPSIS¶
xosview [options]DESCRIPTION¶
xosview is a monitor which displays the status of several system parameters. These include CPU usage, load average, memory, swap space, network usage and more. Each resource is displayed as a horizontal bar which is separated into color coded regions showing how much of the resource is being put to a particular use. xosview runs on several platforms (Linux, NetBSD, FreeBSD, OpenBSD, DragonflyBSD, some Solaris systems, IRIX 6.5, HPUX and GNU). Not all of the meters described below are supported on all platforms. Some of the meters may appear different depending upon the platform xosview is running on. Note that *BSD is used as an abbreviation for all the supported BSD operating systems (NetBSD, FreeBSD, OpenBSD, DragonflyBSD). Load: Kernel reported load averageall platforms : load
Linux : load | CPU frequency
*BSD : load | CPU frequency CPU Usage
Linux : user | nice | system | soft-interrupt | interrupt | io-wait |
guest | niced guest | stolen | idle
*BSD : user | nice | system | interrupt | idle
IRIX : user | system | interrupt | wait | idle
HPUX : user | nice | system | interrupt | idle Memory Usage
Linux : used | buffers | slab | map | cache | free
FreeBSD: active | inactive | wired | cache | free
DFBSD : active | inactive | wired | cache | free
OpenBSD: active | inactive | wired | free
NetBSD : active | inactive | wired | free
IRIX : kernel | fs | user | free
HPUX : text | used | other | free
GNU : active | inactive | wired | free Swap Usage
Linux : used | free
*BSD : used | free
HPUX : used | free
GNU : used | free Disk Usage: Throughput to/from local disk, per second
Linux : in | out | idle
*BSD : in | out | idle Page Swapping: Pages to/from swap, per second
Linux : in | out | idle
*BSD : in | out | idle
HPUX : in | out | idle
GNU : in | out | idle Network Usage
Linux : in | out | idle
*BSD : in | out | idle GFX Usage: Framebuffer exchanges, per second
IRIX : swapbuffers Interrupts: "leds" which blink when an interrupt occurs
Linux : IRQs
*BSD : IRQs Interrupt Rate: Per second
*BSD : interrupts | free Serial Port Status: "leds" which show the serial port parameters
Linux : LSR and MSR Battery Level: charge and status of batteries
Linux : available | used
*BSD : available | used RAID: State of disks in a software RAID array
Linux : disk0 disk1 disk2 ... diskN | rebuild Wireless Link
Linux : quality Temperature sensors
Shows readings from temperature sensors.
Linux : ACPI or i2c/hwmon or Intel Core/AMD K8+ sensors
*BSD : i2c or Intel Core/AMD K8+ sensors Typing a 'q' in the window will terminate xosview.
OPTIONS¶
Most of these command line options are just a convenient way to set one or more of xosview's resources. Please see the RESOURCES section for more details on what the resource is for. -vDisplays the version number.
-name name
Sets the Resource name xosview will use (same as the
-name option for typical X applications like xterm). When performing resource
lookups, xosview will look under name, and then under ``xosview''. For
an example, perform the following (as documented in README.netbsd):
xrdb -merge Xdefaults.stipple
xosview -name xosvstipple &
xosview -name xosvstipplebw &
-display display
xrdb -merge Xdefaults.stipple
xosview -name xosvstipple &
xosview -name xosvstipplebw &
Sets the X display to display. This option
overrides the xosview*display resource.
-font font
Specifies the font xosview will use for labels. This
option overrides the xosview*font resource.
-title title
This option sets the name xosview will tell the window
manager to use for the X window and icon. This option overrides the
xosview*title resource.
-geometry geometry_string
Sets the X geometry to geometry_string. This
option overrides the xosview*geometry resource.
-captions
This option overrides the xosview*captions resource. It
is equivalent to setting xosview*captions to "False".
+captions
This option overrides the xosview*captions resource. It
is equivalent to setting xosview*captions to "True".
-labels
This option overrides the xosview*labels resource. It is
equivalent to setting xosview*labels to "False".
+labels
This option overrides the xosview*labels resource. It is
equivalent to setting xosview*labels to "True".
-usedlabels
This option overrides the xosview*usedlabels resource. It
is equivalent to setting xosview*usedlabels to "False".
+usedlabels
This option overrides the xosview*usedlabels resource. It
is equivalent to setting xosview*usedlabels to "True".
-cpu
This option overrides the xosview*cpu resource. It is
equivalent to setting xosview*cpu to "False".
+cpu
This option overrides the xosview*cpu resource. It is
equivalent to setting xosview*cpu to "True".
+cpus
Force the display of all CPUs in the system. This option
is equivalent to setting xosview*cpuFormat to "all".
-load
This option overrides the xosview*load resource. It is
equivalent to setting xosview*load to "False".
+load
This option overrides the xosview*load resource. It is
equivalent to setting xosview*load to "True".
-mem
This option overrides the xosview*mem resource. It is
equivalent to setting xosview*mem to "False".
+mem
This option overrides the xosview*mem resource. It is
equivalent to setting xosview*mem to "True".
-swap
This option overrides the xosview*swap resource. It is
equivalent to setting xosview*swap to "False".
+swap
This option overrides the xosview*swap resource. It is
equivalent to setting xosview*swap to "True".
-battery
This option overrides the xosview*battery resource. It is
equivalent to setting xosview*battery to "False".
+battery
This option overrides the xosview*battery resource. It is
equivalent to setting xosview*battery to "True".
-gfx
This option overrides the xosview*gfx resource. It is
equivalent to setting xosview*gfx to "False".
+gfx
This option overrides the xosview*gfx resource. It is
equivalent to setting xosview*gfx to "True".
-wireless
This option overrides the xosview*wireless resource. It
is equivalent to setting xosview*wireless to "False".
+wireless
This option overrides the xosview*wireless resource. It
is equivalent to setting xosview*wireless to "True".
-net
This option overrides the xosview*net resource. It is
equivalent to setting xosview*net to "False".
+net
This option overrides the xosview*net resource. It is
equivalent to setting xosview*net to "True".
-network maxbandwidth -networkBW maxbandwidth -networkBandwidth
maxbandwidth
These options override the xosview*netBandwidth resource.
They cause xosview to display a meter that will shows network usage, with a
maximum bandwidth of maxbandwidth. Notice that setting the bandwidth to
0 no longer disables the meter -- use the ``-net'' option instead.
-page
This option overrides the xosview*page resource. It is
equivalent to setting xosview*page to "False".
+page
This option overrides the xosview*page resource. It is
equivalent to setting xosview*page to "True".
-pagespeed val
This option overrides the xosview*pageBandWidth resource.
The resource xosview*pageBandWidth will be set to val.
-disk
This option overrides the xosview*disk resource. It is
equivalent to setting xosview*disk to "False".
+disk
This option overrides the xosview*disk resource. It is
equivalent to setting xosview*disk to "True".
-int
This option overrides the xosview*int resource. It is
equivalent to setting xosview*int to "False".
+int
This option overrides the xosview*int resource. It is
equivalent to setting xosview*int to "True".
-ints +ints -interrupts +interrupts
Equivalent to -int and +int.
-irqrate
This option overrides the xosview*irqrate resource. It is
equivalent to setting xosview*irqrate to "False".
+irqrate
This option overrides the xosview*irqrate resource. It is
equivalent to setting xosview*irqrate to "True".
-intrate +intrate
Equivalent to -irqrate and +irqrate.
-lmstemp
This option overrides the xosview*lmstemp resource. It is
equivalent to setting xosview*lmstemp to "False".
+lmstemp
This option overrides the xosview*lmstemp resource. It is
equivalent to setting xosview*lmstemp to "True".
-coretemp
This option overrides the xosview*coretemp resource. It
is equivalent to setting xosview*coretemp to "False".
+coretemp
This option overrides the xosview*coretemp resource. It
is equivalent to setting xosview*coretemp to "True".
-acpitemp
This option overrides the xosview*acpitemp resource. It
is equivalent to setting xosview*acpitemp to "False".
+acpitemp
This option overrides the xosview*acpitemp resource. It
is equivalent to setting xosview*acpitemp to "True".
-bsdsensor
This option overrides the xosview*bsdsensor resource. It
is equivalent to setting xosview*bsdsensor to "False".
+bsdsensor
This option overrides the xosview*bsdsensor resource. It
is equivalent to setting xosview*bsdsensor to "True".
-xrm resource_string
This switch allows any of xosview's resources to be set
on the command line. An example of how the xosview*memFreeColor could be set
using this option is shown below (Note the use of " to prevent the shell
from expanding ´*´ or from creating two separate arguments,
´xosview*memfreeColor:´ and ´purple´):
-xrm "xosview*memFreeColor: purple"
X RESOURCES¶
The following is a list of X resources supported by xosview. Each has a default value assigned to it. These values can be found in the file Xdefaults which can be obtained in the source distribution of xosview. They can be overridden in the usual places (/usr/lib/X11/app-defaults/XOsview, $HOME/.Xdefaults, etc.). It should be noted that it is OK to have a resource defined for a port of xosview that does not support the feature the resource configures. Xosview will simply ignore the resources that are set for it but not supported on a given platform. General Resources xosview*title: nameThe string that xosview will use for the X window title.
Normally xosview will use 'xosview@machine_name' for a title. This resource
overrides the default behavior.
xosview*geometry: geometry_string
This is a standard X geometry string that defines the
size and location of the X window used by xosview.
xosview*display: name
The name of the display where xosview will contact the X
server for drawing its window.
xosview*pixmapName: name
The filename of an X pixmap (xpm) file for use as a
background image.
xosview*captions: (True or False)
If True then xosview will display meter captions.
xosview*labels: (True or False)
If True then xosview will display meter labels.
xosview*meterLabelColor: color
The color to use for the meter labels.
xosview*usedlabels: (True or False)
If True then xosview will display labels that show the
percentage of the resource (or absolute amount, depending on the meter) being
used. This option requires that the labels option also be set to True.
xosview*usedLabelColor: color
The color to use for "used" labels.
xosview*borderwidth: width
The width of the border for the xosview window.
xosview*font: font
This is the font that xosview will use.
xosview*background: color
This is the color that will be used for the
background.
xosview*foreground: color
This is the color that will be used for the
foreground.
xosview*enableStipple: (True or False)
Change to true to try stipple support. This is primarily
for users stuck with 1-bit monitors/display cards. Try setting enableStipple
true. Please give us feedback on this, if you use it. It needs some more work,
but no one has given us any feedback so far.
xosview*graphNumCols: number
This defines the number of sample bars drawn when a meter
is in scrolling graph mode. This also has the side-effect of defining the
width of the graph columns. This is only used by meters which have graph mode
enabled.
Load Meter Resources
xosview*load: (True or False)
If True then xosview will display a load meter.
xosview*loadProcColor: color
This is the color that the load meter will use to display
the load average when it is below the warning threshold.
xosview*loadWarnColor: color
This is the color that the load meter will use once the
load average is above the warning but below the critical load threshold.
xosview*loadCritColor: color
This is the color that the load meter will use once the
load average is above critical load threshold.
xosview*loadIdleColor: color
The load meter will use this color to display the idle
field.
xosview*loadPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the load meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*loadWarnThreshold: int
This number (which must be an integer >= 1) sets the
value at which the loadmeter changes its status and color from
"normal" to "warning". The default value is the number of
processors.
xosview*loadCritThreshold: int
This number (which must be an integer >= 1) sets the
value at which the loadmeter changes its status and color from
"warning" to "critical". The default value is four times
the warning threshold.
xosview*loadDecay: (True or False)
You should probably leave this at the default value
(False). The load is already a time-averaged value!
xosview*loadGraph: (True or False)
If this is set to True then the load meter will be drawn
as a horizontally scrolling bargraph showing the state value verses
time.
xosview*loadUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
xosview*loadCpuSpeed: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
Display the current CPU speed in the load meter.
CPU Meter Resources
xosview*cpu: (True or False)
If True then xosview will display a cpu meter. On Linux
and IRIX SMP machines, the resource cpuFormat defines how meters are created
for multiple CPUs.
xosview*cpuUserColor: color
The cpu meter will use this color to display the cpu user
time field.
xosview*cpuNiceColor: color
The cpu meter will use this color to display the cpu nice
time field.
xosview*cpuSystemColor: color
The cpu meter will use this color to display the cpu
system time field.
xosview*cpuInterruptColor: color
The cpu meter will use this color to display the cpu hard
interrupt time field.
xosview*cpuSInterruptColor: color
The cpu meter will use this color to display the cpu soft
interrupt time field.
xosview*cpuWaitColor: color
The cpu meter will use this color to display the cpu IO
waiting time field.
xosview*cpuGuestColor: color
The cpu meter will use this color to display the cpu
virtualization guest time field.
xosview*cpuNiceGuestColor: color
The cpu meter will use this color to display the cpu
niced virtualization guest time field.
xosview*cpuStolenColor: color
The cpu meter will use this color to display the cpu
involuntary wait time field.
xosview*cpuFreeColor: color
The cpu meter will use this color to display the cpu idle
time field.
xosview*cpuPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the cpu meter waits between updates. A value
of 1 has xosview update the meter 10 times per second (the fastest). A value
of 600 would cause xosview to update the meter once a minute.
xosview*cpuDecay: (True or False)
If True then the cpu meter will be split vertically in
two. The top half will show the instantaneous state, while the bottom half
will display a decaying average of the state.
xosview*cpuGraph: (True or False)
If this is set to True then the cpu meter will be drawn
as a horizontally scrolling bargraph showing the state value verses
time.
xosview*cpuUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
xosview*cpuFormat: (single, all, both or auto)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If `single', only a cumulative meter for all CPU usage is
created. `all' creates a meter for each CPU, but no cumulative meter. `both'
creates one cumulative meter and one for each CPU. `auto' makes a choice based
on the number of CPUs found.
xosview*cpuFields: USED/USR/NIC/SYS/INT/SI/HI/WIO/GST/NGS/STL/IDLE
The set of fields to show in Linux CPU meter instead of
the default. Possible fields are:
USED:
Memory Meter Resources
xosview*mem: (True or False)
Combine all used CPU time into one field. This is the sum
of user, nice, system, soft and hard interrupts, guest, niced guest and stolen
times. None of these, except stolen, may be defined together with
`USED'.
IDLE:
Time spent doing nothing. Includes I/O wait if it is not
defined separately.
USR:
Time spent in user mode processes. Includes nice, guest
and niced guest if those are not defined separately.
NIC:
Time spent in niced user mode processes. Includes niced
guest if neither it nor guest is not defined separately.
SYS:
Time spent in kernel code. Includes soft and hard
interrupt as well as stolen time if those are not defined separately.
INT:
Combines soft and hard interrupt handling times into one
field.
SI:
Time the kernel used to handle soft interrupts. Available
on Linux kernel 2.6.0 and higher.
HI:
Time the kernel used to handle hard interrupts. Available
on Linux kernel 2.6.0 and higher.
WIO:
Time spent waiting for I/O to complete. Available on
Linux kernel 2.6.0 and higher.
GST:
Time spent running guest OS in virtual machine. Includes
niced guest if it is not defined separately. Available on Linux kernel 2.6.24
and higher.
NGS:
Time spent running niced guest OS in virtual machine.
Available on Linux kernel 2.6.32 and higher.
STL:
Involuntary wait time when running as guest in virtual
machine. Available on Linux kernel 2.6.11 and higher.
Most combinations are possible (see above for restrictions), but at least `USED'
or `USR' and `SYS' need to be defined. `IDLE' field is added
automatically.If True then xosview will display a mem meter.
xosview*memUsedColor: color
The mem meter will use this color to display the used
memory field.
xosview*memSharedColor: color
The mem meter will use this color to display the shared
memory field.
xosview*memBufferColor: color
The mem meter will use this color to display the buffer
memory field.
xosview*memCacheColor: color
The mem meter will use this color to display the cache
memory field.
xosview*memFreeColor: color
The mem meter will use this color to display the free
memory field.
xosview*memSharedColor: color
The mem meter will use this color to display the shared
memory field.
xosview*memTextColor: color
The mem meter will use this color to display the HP text
memory field.
xosview*memOtherColor: color
The mem meter will use this color to display the HP
``other'' memory field.
xosview*memActiveColor: color
The mem meter will use this color to display the *BSD
active memory field.
xosview*memInactiveColor: color
The mem meter will use this color to display the *BSD
inactive memory field.
xosview*memWiredColor: color
The mem meter will use this color to display the *BSD
wired memory field.
xosview*memSlabColor: color
The mem meter will use this color to display the Linux
in-kernel data structures field.
xosview*memMapColor: color
The mem meter will use this color to display the Linux
memory mapped files field.
xosview*memPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the mem meter waits between updates. A value
of 1 has xosview update the meter 10 times per second (the fastest). A value
of 600 would cause xosview to update the meter once a minute.
xosview*memDecay: (True or False)
If True then the mem meter will be split vertically in
two. The top half will show the instantaneous state, while the bottom half
will display a decaying average of the state.
xosview*memGraph: (True or False)
If this is set to True then the mem meter will be drawn
as a horizontally scrolling bargraph showing the state value verses
time.
xosview*memUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Swap Meter Resources
xosview*swap: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a swap meter.
xosview*swapUsedColor: color
The swap meter will use this color to display the used
swap field.
xosview*swapFreeColor: color
The swap meter will use this color to display the free
swap field.
xosview*swapPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the swap meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*swapDecay: (True or False)
If True then the swap meter will be split vertically in
two. The top half will show the instantaneous state, while the bottom half
will display a decaying average of the state.
xosview*swapGraph: (True or False)
If this is set to True then the swap meter will be drawn
as a horizontally scrolling bargraph showing the state value verses
time.
xosview*swapUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Page Swapping Meter Resources
xosview*page: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a page meter.
xosview*pageBandWidth: maxEvents
This number is used to specify the expected maximum
bandwidth (in events / sec) for the page meter. When the expected maximum
bandwidth ( maxEvents) is exceeded then the page meter will display the
relative percentage of page swapping (25% in, 75% out).
xosview*pageInColor: color
The page meter will use this color to display the page-in
field.
xosview*pageOutColor: color
The page meter will use this color to display the
page-out field.
xosview*pageIdleColor: color
The page meter will use this color to display the idle
field.
xosview*pagePriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the page meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*pageDecay: (True or False)
If True then the page meter will be split vertically in
two. The top half will show the instantaneous state, while the bottom half
will display a decaying average of the state.
xosview*pageGraph: (True or False)
If this is set to True then the page meter will be drawn
as a horizontally scrolling bargraph showing the state value verses
time.
xosview*pageUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Gfx Meter Resources
xosview*gfx: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True xosview will display the GfxMeter. The value is
sampled once per second, due to the usage of sadc to sample data.
xosview*gfxWarnColor: color
This is the color that the gfx meter will use once the
warn state is reached.
xosview*gfxAlarmColor: color
This is the color that the gfx meter will use once the
alarm state is reached.
xosview*gfxSwapColor: color
This is the color that the gfx meter will use in normal
state
xosview*gfxIdleColor: color
The gfx meter will use this color to display the idle
field.
xosview*gfxPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the gfx meter waits between updates. A value
of 1 has xosview update the meter 10 times per second (the fastest). A value
of 600 would cause xosview to update the meter once a minute.
xosview*gfxWarnThreshold: int
This number (which must be an integer >= 1) of
swapbuffers per second and pipe at which the gfxmeter changes its status and
color from "normal" to "warn". The default value is
60.
xosview*gfxAlarmThreshold: int
This number (which must be an integer >=
gfxWarnThreshold) of swapbuffers per second and pipe at which the gfxmeter
changes its status and color from "warn" to "alarm". The
default value is 120.
xosview*gfxDecay: (True or False)
You should probably leave this at the default value
(False). The gfx does not work in decay mode.
xosview*gfxGraph: (True or False)
If this is set to True then the gfx meter will be drawn
as a horizontally scrolling bargraph showing the state value verses
time.
xosview*gfxUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Network Meter Resources
xosview*net: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True xosview will display the NetMeter. Linux users
will have to configure their kernels and setup some ip accounting rules to
make this work. See the file README.linux which comes with the xosview
distribution for details.
xosview*netBandwidth: maxBytes
This number is used to specify the expected maximum
bandwidth (in bytes / sec) for the meter. When the expected maximum bandwidth
( maxBytes) is exceeded then the network meter will display the
relative percentage of network usage (25% incoming, 75% outgoing).
xosview*netIface: interface
If False, xosview will display the data
received/transmitted by any of the network interfaces. Otherwise, xosview will
only display the data received/transmitted by the specified network interface.
If the name is prepended with '-' sign, the data in that interface is
ignored.
xosview*netInColor: color
The net meter will use this color to display the incoming
field.
xosview*netOutColor: color
The net meter will use this color to display the outgoing
field.
xosview*netBackground: color
This is the color that the network meter will use for the
"idle" field.
xosview*netPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the net meter waits between updates. A value
of 1 has xosview update the meter 10 times per second (the fastest). A value
of 600 would cause xosview to update the meter once a minute.
xosview*netDecay: (True or False)
If True then the net meter will be split vertically in
two. The top half will show the instantaneous state, while the bottom half
will display a decaying average of the state.
xosview*netGraph: (True or False)
If this is set to True then the net meter will be drawn
as a horizontally scrolling bargraph showing the state value verses
time.
xosview*netUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
NFSStats (Client) Resources
xosview*NFSStats: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a meter to monitor NFS
client stats.
xosview*NFSStatReTransColor: color
The color to be used for retransmit stats.
xosview*NFSStatAuthRefrshColor: color
The color to be used for auth refresh stats.
xosview*NFSStatCallsColor: color
The color to be used for call stats.
xosview*NFSStatIdleColor: color
The color to be used for idle stats.
NFSDStats (Server) Resources
xosview*NFSDStats: (True or False)
If True xosview will display a meter for NFS
server/daemon stats.
xosview*NFSDStatCallsColor: color
The color to be used for call stats.
xosview*NFSDStatBadCallsColor: color
The color to be used for bad stats.
xosview*NFSDStatUDPColor: color
The color to be used for UDP stats.
xosview*NFSDStatTCPColor: color
The color to be used for TCP stats.
xosview*NFSDStatIdleColor: color
The color to be used for idle stats.
Serial Meter Resources
xosview*serial(0-9): (True, False, or portBase)
If True then xosview will display a serial meter for
ttySx. The portbase will be autodetected. Because autodetection can fail, (if
the port is locked by ppp/slip for example) you can specify the portbase
instead of "True". If a portBase is used then xosview will use it
instead of trying to autodetect.
For this to work on Linux xosview needs to be suid root in order to have access
to the ports. See the file README.linux which comes with the xosview
distribution for more details.
xosview*serialOnColor: color
This is the color the serial meter will use for bits that
are set.
xosview*serialOffColor: color
This is the color the serial meter will use for bits that
are not set.
xosview*serialPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the serial meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
Interrupt Meter Resources
xosview*interrupts: (True or False)
If True then xosview will display an interrupt
meter.
xosview*intSeparate: (True of False)
If True then xosview will display one interrupt meter per
CPU on SMP machines. If False only one meter is displayed. Default:
True.
xosview*intOnColor: color
This is the color that will be used to show
"active" interrupts.
xosview*intOffColor: color
This is the color that will be used to show
"inactive" interrupts.
xosview*intPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the int meter waits between updates. A value
of 1 has xosview update the meter 10 times per second (the fastest). A value
of 600 would cause xosview to update the meter once a minute.
Lm Sensors Temperature Resources
xosview*lmstemp: (True or False)
If True then xosview will display a lmstemp meter.
xosview*lmstempHighest: 100
Highest temp value displayed, default 100.
xosview*lmstempActColor: color
Color of actual temperature.
xosview*lmstempHighColor: color
Color above alarm temperature, also used to indicate
alarm.
xosview*lmstempIdleColor: color
Color between actual and alarm temperatures.
xosview*lmstemp N: filename
Name of temperature file from /proc/sys/dev/sensors/*/*
or /sys/class/hwmon/*/*, N=1... Also absolute path is accepted. Note that if
more files with same name exists, only the first is found unless absolute path
is used. For example,
xosview*lmstemp1: temp
xosview*lmstemp2: remote_temp
xosview*lmstempLabel N: Labelstring
N-th label for above temperatures, default is TMP.
xosview*lmstempPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the lmstemp meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*lmstempUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
ACPI Temperature Resources
xosview*acpitemp: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a acpitemp meter.
xosview*acpitempHighest: 100
Highest temp value displayed, default 100. If
acpihighN is given, the value is read from there instead.
xosview*acpitempActColor: color
Color of actual temperature.
xosview*acpitempHighColor: color
Color above alarm temperature, also used to indicate
alarm.
xosview*acpitempIdleColor: color
Color between actual and alarm temperatures.
xosview*acpitemp N: filename
Name of temperature file from /proc/acpi/thermal_zone or
/sys/devices/virtual/thermal. Note that the last directory part must be given,
e.g. TZ0/temperature. Absolute path can also be used.
xosview*acpihigh N: filename
Name of high value/trip point file from
/proc/acpi/thermal_zone or /sys/devices/virtual/thermal, or an absolute path
to one.
xosview*acpitempLabel N: Labelstring
N-th label for above temperatures, default is TMP.
xosview*acpitempPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the acpitemp meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*acpitempUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Intel Core / AMD K8+ Temperature Sensor Resources
xosview*coretemp: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a coretemp meter.
xosview*coretempHighest: 100
Highest temp value displayed, default 100. If none is
given, TjMax value is used, if available.
xosview*coretempActColor: color
Color of actual temperature.
xosview*coretempHighColor: color
Color above alarm temperature, also used to indicate
alarm.
xosview*coretempIdleColor: color
Color between actual and alarm temperatures.
xosview*coretemp NPackage: 0
The number of physical CPU for meter N on Linux.
Currently only one physical CPU can be shown per meter.
xosview*coretemp NDisplayType: (separate, average or maximum)
This resource tells xosview how to display the
temperature for meter N. The formats work as follows:
separate:
xosview*coretempPriority: priority
Display one meter for each CPU core of a multi-core CPU.
This is the default.
average:
Display average temperature of a multi-core CPU.
maximum:
Display the highest core temperature of a multi-core
CPU.
This number (which must be an integer >= 1) sets the
number of tenths of a second that the coretemp meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*coretempUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
*BSD Sensor Resources
xosview*bsdsensor: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a bsdsensor
meter.
xosview*bsdsensorActColor: color
Color of actual value.
xosview*bsdsensorHighColor: color
Color above alarm value, also used to indicate
alarm.
xosview*bsdsensorIdleColor: color
Color between actual and alarm values.
xosview*bsdsensor N: name.type
Here, the name is the sensor driver, and type is the
wanted value. Also static numerical value is accepted for bsdsensorHigh
N.
You can find the correct pair for OpenBSD and DragonflyBSD with systat command,
e.g.
xosview*bsdsensor1: it0.temp1
xosview*bsdsensorHigh1: 100
On NetBSD, you can find the driver name with envstat
command. Value name for the actual reading is typically 'cur-value' and for
alarm level 'max-critical', e.g.
xosview*bsdsensor2: coretemp0.cur-value
xosview*bsdsensorHigh2: coretemp0.max-critical
For all possible NetBSD value names, refer to envstat
source code.
FreeBSD has no sensor drivers as of version 9.0. However,
ACPI thermal zones can be used by defining the sysctl node below
hw.acpi.thermal, e.g.
xosview*bsdsensor1: tz0.temperature
xosview*bsdsensorHigh1: tz0._CRT
ACPI thermal zones work similarly on DragonflyBSD as
well.
xosview*bsdsensorLabel N: Labelstring
N-th label for above meters, default is
SENN.
xosview*bsdsensorPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the bsdsensor meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*bsdsensorUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Battery Meter Resources
xosview*battery: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a battery meter. Linux
users will need to have APM or ACPI support in their kernels for this to work.
For both APM and ACPI, xosview shows the status/sum of all batteries.
Additionally - the legend text gets changed/adjusted to reflect the current
state (charging/low/critical/etc.) of the battery/batteries.
xosview*batteryLeftColor: color
This is the color that will be used to show the amount of
battery power left.
xosview*batteryUsedColor: color
This is the color that will be used to show the amount of
battery power used.
xosview*batteryChargeColor: color
This is the color that will be used as 'left' - if the
batteries get charged.
xosview*batteryFullColor: color
This is the color that will be used as 'left' - if the
batteries are fully charged. APM and ACPI does provide this info, but not all
machines actually do so.
xosview*batteryLowColor: color
APM only - the 'left' color that will indicate a low
battery. Depends on the machine - e.g. below 25% remaining capacity.
xosview*batteryCritColor: color
APM case: the 'left' color if APM indicates 'critical'
state. (less than 5%) ACPI case: the 'left' color if the remaining capacity is
below the alarm value. (which can be set by the user in
/proc/acpi/battery/BAT[01]/alarm )
xosview*batteryNoneColor: color
If no battery is present - or all batteries get removed
(while on AC).
xosview*batteryPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the battery meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*batteryUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Wireless Meter Resources
xosview*wireless: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display the link quality of
each wireless connection. Note that the graph will *never* show up, if you
don't have any wireless devices, or no wireless extensions in the kernel
(/proc/net/wireless). Default is true.
xosview*PoorQualityColor: color
This is the color for the quality field when between 0
and 6.
xosview*FairQualityColor: color
This is the color for the quality field when between 7
and 14.
xosview*GoodQualityColor: color
This is the color for the quality field when higher than
14.
xosview*wirelessUsedColor: color
This is the background color.
xosview*wirelessPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the wireless meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*wirelessDecay: (True or False)
If True then the wireless meter will be split vertically
in two. The top half will show the instantaneous state, while the bottom half
will display a decaying average of the state.
xosview*wirelessUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Disk Meter Resources
xosview*disk: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a disk meter.
xosview*diskInColor: color
The disk meter will use this color to display the reads
field.
xosview*diskOutColor: color
The disk meter will use this color to display the writes
field.
xosview*diskIdleColor: color
The disk meter will use this color to display the idle
field.
xosview*diskBandwidth: bandwidth
This number is used to specify the expected maximum
bandwidth in bytes per second for the disk meter.
xosview*diskWriteColor: color
This color will be used for the linux meter to show
writes.
xosview*diskReadColor: color
This color will be used for the linux meter to show
reads.
xosview*diskPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the disk meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*diskDecay: (True or False)
If True then the disk meter will be split vertically in
two. The top half will show the instantaneous state, while the bottom half
will display a decaying average of the state.
xosview*diskGraph: (True or False)
If this is set to True then the disk meter will be drawn
as a horizontally scrolling bargraph showing the state value verses
time.
xosview*diskUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
RAID Meter Resources
xosview*RAID: (True or False)
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
If True then xosview will display a RAID meter.
xosview*RAIDdevicecount: int
Please enter your RAID device count (n) here or 0 if you
don't have any supported RAID devices. xosview then will display n RAID state
displays.
xosview*RAIDdiskOnlineColor: color
xosview*RAIDdiskFailureColor: color
These colors will be used for indicating working/online
or failed/offline disks. The order (from left to right) is the same as in
/proc/mdstat.
xosview*RAIDresyncdoneColor: color
xosview*RAIDresynctodoColor: color
xosview*RAIDresynccompleteColor: color
If a resync/rebuild of the RAID array is in progress, the
"done" and "todo" colors will be used. If no
rebuild/resync is running, then the "complete" color will be
shown.
xosview*RAIDPriority: priority
This number (which must be an integer >= 1) sets the
number of tenths of a second that the RAID meter waits between updates. A
value of 1 has xosview update the meter 10 times per second (the fastest). A
value of 600 would cause xosview to update the meter once a minute.
xosview*RAIDUsedFormat: (float, percent or autoscale)
This resource tells xosview how to display
"used" labels. The formats work as follows:
float:
Display the value as a floating point number.
percent:
Display the value as a percentage of the total.
autoscale:
Display the absolute value and automatically print the
units (K, M, or G) as appropriate.
OBTAINING¶
This version of xosview is distributed from the following site:AUTHORS¶
Mike Romberg <mike.romberg@noaa.gov>Original author, Linux and HPUX ports.
Brian Grayson <bgrayson@netbsd.org>
NetBSD port and most of the nice enhancements for version
1.4, initial work on FreeBSD port.
Scott McNab <jedi@tartarus.uwa.edu.au>
Added the scrolling graph mode.
Tom Pavel <pavel@slac.stanford.edu>
Most of the FreeBSD support, more resource-handling
improvements.
Greg Onufer <exodus@cheers.bungi.com>
SunOS port.
Stefan Eilemann <eilemann@gmail.com>
IRIX 6.5 port.
Sheldon Hearn <axl@iafrica.com>
FreeBSD libdevstat-based diskmeter support.
David W. Talmage <talmage@jefferson.cmf.nrl.navy.mil>
Added battery-meter support to NetBSD.
Oleg Safiullin <form@openbsd.org>
OpenBSD interrupt-meter support.
Werner Fink <werner@suse.de>
Originator of the loadmeter.
Massimiliano Ghilardi <ghilardi@cibs.sns.it>
Linux pagemeter.
Carsten Schabacker <cschaba@spock.central.de>
Made extensions to the serial-meter.
Paal Beyer <pbeyer@online.no>
Ported the linux memstat kernel module to linux-2.1
Jerome Forissier <forissier@isia.cma.fr>
Author of the Linux SMP kernel patch which xosview uses
to display meters for each CPU.
Tomer Klainer <mandor@cs.huji.ac.il>
Initial port to BSDI.
Arno Augustin <Arno.Augustin@3SOFT.de>
Solaris disk and network meters.
Alberto BARSELLA <ishark@lsh01.univ-lille1.fr>
Fixes for linux diskmeter + ip_chains support
Thomas Waldmann <ThomasWaldmann@gmx.de>
Linux raid meter, bitfieldmeter. Many cosmetic
fixes.
Leopold Toetsch <lt@toetsch.at>
Linux lms temp meter.
David O'Brien <obrien@nuxi.com>
FreeBSD 4.* updates, and a few other suggestions.
Christos Zoulas <christos@netbsd.org>
C++ standard compliance and other NetBSD fixes.
Tim Ehlers <tehlers@gwdg.de>
Wireless Link-Meter for Linux.
Mark Hills <mark@pogo.org.uk>
Bug fixes and general caretaking.
Tomi Tapper <tomi.o.tapper@student.jyu.fi>
Temperature sensor, and FreeBSD updates.
Raymond S Brand (rsbx@acm.org)
Misc fixes.
And many others who have sent in small fixes and improvements.3rd Berkeley Distribution |