table of contents
other versions
- jessie 0.49.2-3+deb8u2
SAM2P(1) | General Commands Manual | SAM2P(1) |
NAME¶
sam2p - program to convert raster images to PostScript, PDF, and other formatsSYNOPSIS¶
sam2p [options] infile outfileDESCRIPTION¶
This manual page documents briefly the sam2p command. It was written for the Debian distribution because the original program does not have a manual page. The complete documentation can be found in /usr/share/doc/sam2p/README.gz sam2p is a program that converts many raster (bitmap) image formats into Adobe PostScript or PDF files and several other formats. The images are not vectorized. sam2p gives full control to the user to specify standards-compliance, compression, and bit depths. sam2p can operate in two modes: one-liner mode and job mode. In job mode the user has to write a ``job'' file which specifies the conversion parameters and allows full control of all aspects of the final output. This manpage deals only with one-liner mode, see /usr/share/doc/sam2p/README.gz for details on job mode.EXAMPLES¶
To convert an image file to EPS, use:sam2p infile.gif outfile.eps The output format is guessed from the file extension. Optionally, the output format also can be specified as option or as prefix to the output file. For example, the following commands produce postscript level 3:
sam2p infile.gif psl3:outfile.ps
sam2p -ps:3 infile.gif outfile.ps sam2p can include its own (zip and lzw) decompression filter in Postscript files, allowing better compression than normally supported by Postscript level 1:
sam2p -1 -c:zip infile.gif outfile.ps
sam2p -1 -c:lzw infile.gif outfile.ps
OPTIONS¶
- -1, -ps:1, psl1:
- produce Postscript Level 1
- -1c, -ps:1c, pslc:
- produce Postscript Level 1 with the CMYK and `colorimage' extension
- -2, -ps:2, psl2:
- produce Postscript Level 2 (default for postscript)
- -3, -ps:3, psl3:
- produce Postscript Level 3
- -pdf:b0, pdfb1.0:
- produce PDF version 1.0 (BI inline image)
- -pdf:b2, pdfb1.2:
- produce PDF version 1.2 (BI inline image) (default for PDF)
- -pdf:0, pdf1.0:
- produce PDF version 1.0 (XObject image)
- -pdf:2, pdf1.2:
- produce PDF version 1.2 (XObject image)
- -e:0, -e:none
- don't scale
- -e, -e:1, -e:scale
- scale image to fit page
- -e:rot, -e:rotate
- scale and rotate image to fit page (default if output filename has .ps extension)
- -m:dimen
- set all page margins to dimen
- -m:spec:dimen
- set spec margin(s) to dimen (spec can be l, r, t, b, v (top and bottom), h (left and right))
- -m:dpi:res
- set output EPS or PDF to resolution 72*72/res dpi
- -m:dpi:-res
- set output EPS or PDF to resolution res dpi
- -c:none, -c:lzw, -c:zip, -c:rle, -c:fax, -c:dct, -c:jpeg
- select compression type (support depends on output format)
- -j:quiet
- print only error and fatal error messages, suppress warnings, notices etc. Must be put at the beginning of the command line to suppress initial banners, too.
- --
- If not the last argument: treat all further arguments as files (required
if a filename contains a colon or starts with a minus)
SUPPORTED FILE FORMATS¶
- Input formats:
- PNM, PBM, PGM, PPM, XPM, GIF, LBM, TGA, PCX,
- Output formats:
- XWD, BMP, PNG, TIFF6, JPEG, PNM, GIF89a, XPM, PS (levels 1,2,3), EPS (levels 2,3), PDF (1.0 and 1.2) For some formats, sam2p supports transparency. See the README file for more info.
SEE ALSO¶
The program is documented fully in /usr/share/doc/sam2p/README.gzAUTHOR¶
sam2p was written by Szabó Péter <pts@fazekas.hu>. This manual page was written by Stefan Fritsch <sf@sfritsch.de>, for the Debian project (but may be used by others under the terms of the GNU General Public License, Version 2).January 23, 2005 |