NAME¶
mgettydefs - speed and terminal settings used by mgetty
DESCRIPTION¶
The
/etc/gettydefs file contains information used by
mgetty(1) to
set up the speed and terminal settings for a line. It also supplies
information on what the
login prompt should look like.
Many versions of UNIX have a version of
getty(1) that also reads
/etc/gettydefs. Both
mgetty and
getty expect similar
formats in
/etc/gettydefs except that, when used by
mgetty,
extended functionality is available. Even so, the additional functions are
simply ignored by standard
getty, so they can co-exist using the same
file. Note, however, that
mgetty can be compiled to use a file
different from
/etc/gettydefs if your
getty gets upset about the
extensions. This manual page documents
/etc/gettydefs and describes the
extended functionality available when used by
mgetty(1). This document
will refer to
getty(1) except where
mgetty's behaviour is
different.
Each entry in
/etc/gettydefs has the following format:
- label# initial-flags # final-flags # login-prompt #next-label
Each entry is followed by a blank line. The login prompt field can contain
quoted characters which will be converted to other values. The sequences and
their substitutions are:
- \n
- newline
- \r
- carriage return
- \g
- beep
- \b
- backspace
- \v
- vertical tab (VT)
- \f
- formfeed
- \t
- tab
- \L
- portname
- \C
- time in ctime(3) format.
- \N
- number of users currently logged in
- \U
- number of users currently logged in
- \D
- date in DD/MM format
- \T
- time in hh:mm:ss format
- \I
- modem CONNECT attributes
- \sequence
- where "sequence" is a valid strtol format, such as: \0nnn
(octal), \0xnnn (hex), or \nnn (decimal).
Note that standard
getty usually only supports \b, \r and \n.
The various fields are:
- label
- This is the string against which getty tries to match its second
argument. It is often the speed, such as 1200, at which the
terminal is supposed to run, but it need not be (see below).
- initial-flags
- These flags are the initial ioctl(2) settings to which the terminal
is to be set if a terminal type is not specified to getty. The
flags that getty understands are the ones listed in
termio(7)). mgetty is usually compiled for termios(7)
and often has a more complete set than getty.
- Normally only the speed flag is required in the
- initial-flags. getty automatically sets the terminal to raw
input mode and takes care of the other flags. If the "-s" option
is used with mgetty(1) the speed setting is ignored. The
initial-flag settings remain in effect until getty executes
login(1).
- final-flags
- These flags take the same values as the initial-flags and are set
just before getty executes login. The speed flag is again
required, except with mgetty if the -s flag was supplied. Two other
commonly specified final-flags are TAB3, so that tabs are
sent to the terminal as spaces, and HUPCL, so that the line is hung
up on the final close.
- login-prompt
- This entire field is printed as the login-prompt. Unlike the above
fields where white space (a space, tab or new-line) is ignored, they are
included in the login-prompt field. This field is ignored if the
"-p" option has been specified to mgetty(1).
- next-label
- specifies the label to use if the user user types a <break>
character, or getty detects a reception error. Getty
searches for the entry with next-label as its label field
and set up the terminal for those settings. Usually, a series of speeds
are linked together in this fashion, into a closed set; for instance,
2400 linked to 1200, which in turn is linked to 300,
which finally is linked to 2400. next-label is ignored with
mgetty(1).
Several additional composite settings are available for
initial-flags and
final-flags. The following composite flags are supported by
mgetty and are usually supported by
getty:
- SANE
- equivalent to ``stty sane''. (BRKINT, IGNPAR, ISTRIP, ICRNL, IXON, OPOST,
CS8, CREAD, ISIG, ICANON, ECHO, ECHOK)
- ODDP
- Odd parity (CS7, PARENB, PARODD)
- PARITY,EVENP
- even parity (CS7, PARENB)
- -ODDP,-PARITY,-EVENP
- no parity (resets PARENB, PARODD, and sets CS8)
- RAW
- raw I/O (no canonical processing) (turns off OPOST, ICANON)
- -RAW,COOKED
- enable canonical processing (turns on OPOST, ICANON)
- NL
- Ignore newlines. (ICRNL, ONLCR)
- -NL
- Respect newlines (turns INLCR, IGNCR, ICRNL, ONLCR, OCRNL, ONLRET
off)
- LCASE
- Ignore case - treat all as lowercase. (IUCLC, OLCUC, XCASE) Is set if
mgetty believes login is entirely uppercase.
- -LCASE
- Repect case (turns off IUCLC, OLCUC and XCASE)
- TABS
- output tabs as tabs
- -TABS,TAB3
- output tabs as spaces
- EK
- Sets VERASE to "#" and VKILL to CKILL respectively. (note that
while many gettys default VERASE to "#". mgetty defaults
VERASE to backspace.)
Additionally,
mgetty (but not
getty) can set any of the control
characters listed in the
c_cc termio(termios) structure by the use of
two tokens:
<character name> <value>
Eg:
VERASE ^h
The value can be set as ``^<character>'', ``\nnn'' or
``\<character>'' (normal UNIX \ escapes).
See the
termio(7) or
termios(7) manual pages to a list of which
``V'' variables can be changed. Note that many of these can be changed in the
c_cc array, but won't have any effect.
If
getty is called without a second argument, the first entry of
/etc/gettydefs is used by
getty, thus making the first entry of
/etc/gettydefs the default entry. It is also used if
getty
cannot find the specified
label.
Mgetty use a default label of
``n'', but this can be changed in the configuration. If
/etc/gettydefs
itself is missing, there is one entry built into the command which brings up a
terminal at
300 (configuration parameter in
mgetty) baud.
It is strongly recommended that after making or modifying
/etc/gettydefs,
it be run through
getty with the check option to be sure there are no
errors.
EXAMPLES¶
The following two lines show an example of 300/1200 baud toggle, which is useful
for dial-up ports:
- 1200# B1200 HUPCL # B1200 SANE IXANY TAB3 #login: #300
300# B300 HUPCL # B300 SANE IXANY TAB3 #login: #1200
The following line shows a typical 9600 baud entry for a hard-wired connection
(not currently supported for
mgetty):
- 9600# B9600 # B9600 SANE IXANY IXANY ECHOE TAB3 #login: #9600
The following line is a typical smart-modem setup, suitable for
mgetty:
-
19200mg#
B19200 #
B19200 SANE VERASE \b VINTR \003 HUPCL #
\n\D \T \N Users @!login: #19200mg
FILES¶
/etc/gettydefs
SEE ALSO¶
mgetty(8),
getty(8),
login(1),
ioctl(2),
termio(7), termios(7).