other versions
- jessie 3.16.56-1+deb8u1
ENUM IEEE80211_HW_FL(9) | The basic mac80211 driver inte | ENUM IEEE80211_HW_FL(9) |
NAME¶
enum_ieee80211_hw_flags - hardware flagsSYNOPSIS¶
enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL, IEEE80211_HW_RX_INCLUDES_FCS, IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING, IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE, IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, IEEE80211_HW_SIGNAL_UNSPEC, IEEE80211_HW_SIGNAL_DBM, IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC, IEEE80211_HW_SPECTRUM_MGMT, IEEE80211_HW_AMPDU_AGGREGATION, IEEE80211_HW_SUPPORTS_PS, IEEE80211_HW_PS_NULLFUNC_STACK, IEEE80211_HW_SUPPORTS_DYNAMIC_PS, IEEE80211_HW_MFP_CAPABLE, IEEE80211_HW_WANT_MONITOR_VIF, IEEE80211_HW_SUPPORTS_STATIC_SMPS, IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS, IEEE80211_HW_SUPPORTS_UAPSD, IEEE80211_HW_REPORTS_TX_ACK_STATUS, IEEE80211_HW_CONNECTION_MONITOR, IEEE80211_HW_QUEUE_CONTROL, IEEE80211_HW_SUPPORTS_PER_STA_GTK, IEEE80211_HW_AP_LINK_PS, IEEE80211_HW_TX_AMPDU_SETUP_IN_HW, IEEE80211_HW_SUPPORTS_RC_TABLE, IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF, IEEE80211_HW_TIMING_BEACON_ONLY, IEEE80211_HW_SUPPORTS_HT_CCK_RATES, IEEE80211_HW_CHANCTX_STA_CSA, IEEE80211_HW_CHANGE_RUNNING_CHANCTX };
CONSTANTS¶
IEEE80211_HW_HAS_RATE_CONTROLThe hardware or firmware includes rate control, and
cannot be controlled by the stack. As such, no rate control algorithm should
be instantiated, and the TX rate reported to userspace will be taken from the
TX status instead of the rate control algorithm. Note that this requires that
the driver implement a number of callbacks so it has the correct information,
it needs to have the set_rts_threshold callback and must look at the
BSS config use_cts_prot for G/N protection, use_short_slot for
slot timing in 2.4 GHz and use_short_preamble for preambles for CCK
frames.
IEEE80211_HW_RX_INCLUDES_FCS
Indicates that received frames passed to the stack
include the FCS at the end.
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING
Some wireless LAN chipsets buffer broadcast/multicast
frames for power saving stations in the hardware/firmware and others rely on
the host system for such buffering. This option is used to configure the IEEE
802.11 upper layer to buffer broadcast and multicast frames when there are
power saving stations so that the driver can fetch them with
ieee80211_get_buffered_bc.
IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
Hardware is not capable of short slot operation on the
2.4 GHz band.
IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE
Hardware is not capable of receiving frames with short
preamble on the 2.4 GHz band.
IEEE80211_HW_SIGNAL_UNSPEC
Hardware can provide signal values but we don't know its
units. We expect values between 0 and max_signal. If possible please
provide dB or dBm instead.
IEEE80211_HW_SIGNAL_DBM
Hardware gives signal values in dBm, decibel difference
from one milliwatt. This is the preferred method since it is standardized
between different devices. max_signal does not need to be set.
IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
This device needs to get data from beacon before
association (i.e. dtim_period).
IEEE80211_HW_SPECTRUM_MGMT
Hardware supports spectrum management defined in 802.11h
Measurement, Channel Switch, Quieting, TPC
IEEE80211_HW_AMPDU_AGGREGATION
Hardware supports 11n A-MPDU aggregation.
IEEE80211_HW_SUPPORTS_PS
Hardware has power save support (i.e. can go to
sleep).
IEEE80211_HW_PS_NULLFUNC_STACK
Hardware requires nullfunc frame handling in stack,
implies stack support for dynamic PS.
IEEE80211_HW_SUPPORTS_DYNAMIC_PS
Hardware has support for dynamic PS.
IEEE80211_HW_MFP_CAPABLE
Hardware supports management frame protection (MFP, IEEE
802.11w).
IEEE80211_HW_WANT_MONITOR_VIF
The driver would like to be informed of a virtual monitor
interface when monitor interfaces are the only active interfaces.
IEEE80211_HW_SUPPORTS_STATIC_SMPS
Hardware supports static spatial multiplexing powersave,
ie. can turn off all but one chain even on HT connections that should be using
more chains.
IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS
Hardware supports dynamic spatial multiplexing powersave,
ie. can turn off all but one chain and then wake the rest up as required
after, for example, rts/cts handshake.
IEEE80211_HW_SUPPORTS_UAPSD
Hardware supports Unscheduled Automatic Power Save
Delivery (U-APSD) in managed mode. The mode is configured with conf_tx
operation.
IEEE80211_HW_REPORTS_TX_ACK_STATUS
Hardware can provide ack status reports of Tx frames to
the stack.
IEEE80211_HW_CONNECTION_MONITOR
The hardware performs its own connection monitoring,
including periodic keep-alives to the AP and probing the AP on beacon
loss.
IEEE80211_HW_QUEUE_CONTROL
The driver wants to control per-interface queue mapping
in order to use different queues (not just one per AC) for different virtual
interfaces. See the doc section on HW queue control for more details.
IEEE80211_HW_SUPPORTS_PER_STA_GTK
The device's crypto engine supports per-station GTKs as
used by IBSS RSN or during fast transition. If the device doesn't support
per-station GTKs, but can be asked not to decrypt group addressed frames, then
IBSS RSN support is still possible but software crypto will be used. Advertise
the wiphy flag only in that case.
IEEE80211_HW_AP_LINK_PS
When operating in AP mode the device autonomously manages
the PS status of connected stations. When this flag is set mac80211 will not
trigger PS mode for connected stations based on the PM bit of incoming frames.
Use ieee80211_start_ps/ieee8021_end_ps to manually configure the
PS mode of connected stations.
IEEE80211_HW_TX_AMPDU_SETUP_IN_HW
The device handles TX A-MPDU session setup strictly in
HW. mac80211 should not attempt to do this in software.
IEEE80211_HW_SUPPORTS_RC_TABLE
The driver supports using a rate selection table provided
by the rate control algorithm.
IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
Use the P2P Device address for any P2P Interface. This
will be honoured even if more than one interface is supported.
IEEE80211_HW_TIMING_BEACON_ONLY
Use sync timing from beacon frames only, to allow getting
TBTT of a DTIM beacon.
IEEE80211_HW_SUPPORTS_HT_CCK_RATES
Hardware supports mixing HT/CCK rates and can cope with
CCK rates in an aggregation session (e.g. by not using aggregation for such
frames.)
IEEE80211_HW_CHANCTX_STA_CSA
Support 802.11h based channel-switch (CSA) for a single
active channel while using channel contexts. When support is not enabled the
default action is to disconnect when getting the CSA frame.
IEEE80211_HW_CHANGE_RUNNING_CHANCTX
The hardware can change a channel context on-the-fly.
This is needed for channel switch on single-channel hardware. It can also be
used as an optimization in certain channel switch cases with
multi-channel.
DESCRIPTION¶
These flags are used to indicate hardware capabilities to the stack. Generally, flags here should have their meaning done in a way that the simplest hardware doesn't need setting any particular flags. There are some exceptions to this rule, however, so you are advised to review these flags carefully.AUTHOR¶
Johannes Berg <johannes@sipsolutions.net>Author.
COPYRIGHT¶
May 2018 | Kernel Hackers Manual 3.16 |