UAPUTL(1) | General Commands Manual | UAPUTL(1) |
NAME¶
uaputl - configure Marvell uAP wireless driver
SYNOPSIS¶
uaputl [options] <command> [parameters]
DESCRIPTION¶
This manual page documents briefly the uaputl command, which is used to configure the device driver for Marvell's uAP wireless interface.
OPTIONS¶
- -d <debug_level>
- Enable debugging output, level can be 0, 1, or 2.
- -h, --help
- Show summary of options and commands.
- -i <interface>
- Select interface to configure.
- -v
- Show version of program.
COMMANDS¶
For more information on the usage of each command use:
uaputl.exe <command> --help
- sys_config
- Set/get uAP's profile
- sys_info
- Display system info
- sys_reset
- Reset uAP
- bss_start
- Start the BSS
- bss_stop
- Stop the BSS
- sta_deauth
- Deauth client
- sta_list
- Display list of clients
- sys_cfg_ap_mac_address
- Set/get uAP mac address
- sys_cfg_ssid
- Set/get uAP ssid
- sys_cfg_beacon_period
- Set/get uAP beacon period
- sys_cfg_dtim_period
- Set/get uAP dtim period
- sys_cfg_channel
- Set/get uAP radio channel
- sys_cfg_scan_channels
- Set/get uAP radio channel list
- sys_cfg_rates
- Set/get uAP rates
- sys_cfg_rates_ext
- Set/get uAP rates (extended)
- sys_cfg_tx_power
- Set/get uAP tx power
- sys_cfg_bcast_ssid_ctl
- Set/get uAP broadcast ssid
- sys_cfg_preamble_ctl
- Get uAP preamble
- sys_cfg_antenna_ctl
- Set/get uAP tx/rx antenna
- sys_cfg_rts_threshold
- Set/get uAP rts threshold
- sys_cfg_frag_threshold
- Set/get uAP frag threshold
- sys_cfg_radio_ctl
- Set/get uAP radio on/off
- sys_cfg_tx_data_rate
- Set/get uAP tx rate
- sys_cfg_mcbc_data_rate
- Set/get uAP MCBC rate
- sys_cfg_rsn_replay_prot
- Set/get RSN replay protection
- sys_cfg_pkt_fwd_ctl
- Set/get uAP packet forwarding
- sys_cfg_sta_ageout_timer
- Set/get station ageout timer
- sys_cfg_auth
- Set/get uAP authentication mode
- sys_cfg_protocol
- Set/get uAP security protocol
- sys_cfg_wep_key
- Set/get uAP wep key
- sys_cfg_cipher
- Set/get uAP WPA/WPA cipher
- sys_cfg_wpa_passphrase
- Set/get uAP WPA or WPA2 passphrase
- sys_cfg_group_rekey_timer
- Set/get uAP group re-key time
- sys_cfg_max_sta_num
- Set/get uAP max station number
- sys_cfg_retry_limit
- Set/get uAP retry limit number
- sys_cfg_custom_ie
- Set/get custom IE configuration
- sta_filter_table
- Set/get uAP mac filter
- regrdwr
- Read/Write register command
- memaccess
- Read/Write to a memory address command
- rdeeprom
- Read EEPROM
- cfg_data
- Get/Set configuration file from/to firmware
- sys_debug
- Set/Get debug parameter
- sys_cfg_80211d
- Set/Get 802.11D info
- uap_stats
- Get uAP stats
- powermode
- Set/get uAP power mode
- coex_config
- Set/get uAP BT coex configuration
SEE ALSO¶
This manual page was written by Bdale Garbee <bdale@gag.com>, for the Debian project (and may be used by others).
July 20, 2011 |