Scroll to navigation

MSMTPD(1) General Commands Manual MSMTPD(1)

NAME

msmtpd - A minimal SMTP server

SYNOPSIS

msmtpd [option...]

DESCRIPTION

Msmtpd is a minimal SMTP server that pipes mails to msmtp (or some other program) for delivery. It can be used with system services that expect an SMTP server on the local host, or it can be used by end users as a way to handle outgoing mail via msmtp with mail clients that insist on using SMTP. The EXAMPLES section below contains examples for both use cases.
Msmtpd listens on 127.0.0.1 port 25 by default, but can also run without its own network sockets in inetd mode, where it handles a single SMTP session on standard input / output.
In the string that defines the command that msmtpd pipes each mail to, the first occurrence of %F will be replaced with the envelope from address. Furthermore, all recipients of the mail will be appended as arguments. The command must not write to standard output, as that would mess up the SMTP session.
If the command that the mail is piped to reports an error, this is typically reported as a permanent failure by msmtpd (SMTP server return code 554). The command can optionally signal temporary errors by using return codes defined in sysexits.h, e.g. 75 for EX_TEMPFAIL. These will then be reported as temporary failures by msmtpd (SMTP server return code 451), which means the client should try again later.
To prevent abuse, msmtpd will allow only a limited number of concurrent SMTP sessions, and if authentication is active and an authentication failure occurrs, future authentication requests in any SMTP session will (for a limited duration) only be answered after a small delay.

OPTIONS

Print version information
Print help
Start single SMTP session on stdin/stdout
Listen on the given IPv6 or IPv4 address instead of 127.0.0.1
Listen on the given port number instead of 25
Set logging: none (default), syslog, or logging to the given file.
Pipe mails to cmd instead of msmtp. Make sure to end this command with -- to separate options from arguments.
Require authentication with this user name. The password will be retrieved from the given passwordeval command (this works just like passwordeval in msmtp) or, if none is given, from the key ring or, if that fails, from a prompt.

EXAMPLES

Using msmtpd as a system service
Only use a local interface to listen on. Run msmtpd with correct user rights and permissions (e.g. use CAP_NET_BIND_SERVICE to bind to port 25 instead of running as root, or use systemd with inetd service capabilities). Be aware that the pipe command will be run as the same user that msmtpd runs as. Enable logging to syslog with --log=syslog.
Example for managing msmtpd with start-stop-daemon:
# start msmtpd
start-stop-daemon --start --pidfile /var/run/msmtpd.pid --make-pidfile --chuid msmtpd --background --exec /usr/local/bin/msmtpd -- --command '/usr/local/bin/msmtp -f %F --'
# stop msmtpd
start-stop-daemon --stop --pidfile /var/run/msmtpd.pid --remove-pidfile --quiet --signal TERM
Using msmtpd to handle outgoing mail for an SMTP-based mail client
Some mail clients cannot send outgoing mail with a program like msmtp and instead insist on using an SMTP server. You can configure msmtpd to be that SMTP server and hand your outgoing mail over to msmtp.
(Similarly, some mail clients cannot get incoming mail from a local mailbox and insist on using a POP3 or IMAP server. You can configure mpopd to be that POP3 server and serve incoming mail from a local mailbox. See the relevant section in the mpop manual.)
For this purpose, msmtpd should listen on an unprivileged port, e.g. 2500. Furthermore, msmtpd should require authentication because otherwise anyone connecting to it can send mail using your account, even if it's just other users or processes on your local machine.
Let's use the user name msmtpd-user for this purpose. You have two options to manage the password:

Store the password in your key ring, e.g. with secret-tool store --label=msmtpd host localhost service smtp user msmtpd-user. In this case, use the msmtpd option --auth=msmtpd-user.
Store the password in an encrypted file and use the passwordeval mechanism. Example for gpg: msmtpd ... --auth=msmtpd-user,'gpg -q -d ~/.msmtpd-password.gpg'

The complete command then is (using the keyring): msmtpd --port=2500 --auth=msmtpd-user --command='/path/to/your/msmtp -f %F --'
The mail client software must then be configured to use localhost at port 2500 for outgoing mail via SMTP, and to use authentication with user msmtpd-user and the password you chose. The mail client will probably complain that the SMTP server does not support TLS, but in this special case that is ok since all communication between your mail client and msmtpd will stay on the local machine.
This setup also works with multiple mail accounts. Msmtp will pick the correct one based on the envelope-from address given to it via -f %F. You do not need multiple instances of msmtpd for this purpose, and therefore you need only one SMTP server in your mail client configuration.

SEE ALSO

msmtp(1)

2021-09