NAME¶
funcone - cone search of a binary table containing RA, Dec columns
SYNOPSIS¶
funcone <switches> <iname> <oname> <ra[hdr]>
<dec[hdr]> <radius[dr'"]> [columns]
OPTIONS¶
-d deccol:[hdr] # Dec column name, units (def: DEC:d)
-j # join columns from list file
-J # join columns from list file, output all rows
-l listfile # read centers and radii from a list
-L listfile # read centers and radii from a list, output list rows
-n # don't use cone limits as a filter
-r racol:[hdr] # RA column name, units (def: RA:h)
-x # append RA_CEN, DEC_CEN, RAD_CEN, CONE_KEY cols
-X # append RA_CEN, DEC_CEN, RAD_CEN, CONE_KEY cols, output all rows
DESCRIPTION¶
Funcone performs a cone search on the RA and Dec columns of a FITS binary table.
The distance from the center RA, Dec position to the RA, Dec in each row in
the table is calculated. Rows whose distance is less than the specified radius
are output.
The first argument to the program specifies the FITS file, raw event file, or
raw array file. If "stdin" is specified, data are read from the
standard input. Use Funtools Bracket Notation to specify FITS extensions, and
filters. The second argument is the output FITS file. If "stdout" is
specified, the FITS binary table is written to the standard output.
The third and fourth required arguments are the RA and Dec center position. By
default, RA is specified in hours while Dec is specified in degrees. You can
change the units of either of these by appending the character "d"
(degrees), "h" (hours) or "r" (radians). Sexagesimal
notation is supported, with colons or spaces separating hms and dms. (When
using spaces, please ensure that the entire string is quoted.)
The fifth required argument is the radius of the cone search. By default, the
radius value is given in degrees. The units can be changed by appending the
character "d" (degrees), "r" (radians), "'" (arc
minutes) or '"' (arc seconds).
By default, all columns of the input file are copied to the output file.
Selected columns can be output using an optional sixth argument in the form:
"column1 column1 ... columnN"
A seventh argument allows you to output selected columns from the list file when
\-j switch is used. Note that the RA and Dec columns used in the cone
calculation must not be de\-selected.
Also by default, the RA and Dec column names are named "RA" and
"Dec", and are given in units of hours and degrees respectively. You
can change both the name and the units using the \-r [RA] and/or \-d [Dec]
switches. Once again, one of "h", "d", or "r" is
appended to the column name to specify units but in this case, there must be a
colon ":" between the name and the unit specification.
If the
\-l [listfile] switch is used, then one or more of the center RA,
center Dec, and radius can be taken from a list file (which can be a FITS
table or an ASCII column text file). In this case, the third (center RA),
fourth (center Dec), and fifth (radius) command line arguments can either be a
column name in the list file (if that parameter varies) or else a numeric
value (if that parameter is static). When a column name is specified for the
RA, Dec, or radius, you can append a colon followed by "h",
"d", or "r" to specify units (also ' and " for
radius). The cone search algorithm is run once for each row in the list,
taking RA, Dec, and radius values from the specified columns or from static
numeric values specified on the command line.
When using a list, all valid rows from each iteration are written to a single
output file. Use the
\-x switch to help delineate which line of the
list file was used to produce the given output row(s). This switch causes the
values for the center RA, Dec, radius, and row number to be appended to the
output file, in columns called RA_CEN, DEC_CEN, RAD_CEN and CONE_KEY,
respectively. Alternatively, the
\-j (join) switch will append all
columns from the list row to the output row (essentially a join of the list
row and input row), along with the CONE_KEY row number. These two switches are
mutually exclusive.
The
\-X and
\-J switches write out the same data as their lower
case counterparts for each row satisfying a cone search. In addition, these
switches also write out rows from the event file that do not satisfy any cone
search. In such cases, that CONE_KEY column will be given a value of \-1 and
the center and list position information will be set to zero for the given
row. Thus, all rows of the input event file are guaranteed to be output, with
rows satisfying at least one cone search having additional search information.
The
\-L switch acts similarly to the
\-l switch in that it takes
centers from a list file. However, it also implicitly sets the \-j switch, so
that output rows are the join of the input event row and the center position
row. In addition, this switch also writes out all center position rows for
which no event satisfies the cone search criteria of that row. The CONE_KEY
column will be given a value of \-2 for center rows that were not close to any
data row and the event columns will be zeroed out for such rows. In this way,
all centers rows are guaranteed to be output at least once.
If any of "all row" switches (
\-X,
\-J, or
\-L)
are specified, then a new column named JSTAT is added to the output table. The
positive values in this column indicate the center position row number
(starting from 1) in the list file that this data row successful matched in a
cone search. A value of \-1 means that the data row did not match any center
position. A value of \-2 means that the center position was not matched by any
data row.
Given a center position and radius, the cone search algorithm calculates limit
parameters for a box enclosing the specified cone, and only tests rows whose
positions values lie within those limits. For small files, the overhead
associated with this cone limit filtering can cause the program to run more
slowly than if all events were tested. You can turn off cone limit filtering
using the
\-n switch to see if this speeds up the processing
(especially useful when processing a large list of positions).
For example, the default cone search uses columns "RA" and
"Dec" in hours and degrees (respectively) and RA position in hours,
Dec and radius in degrees:
funone in.fits out.fits 23.45 34.56 0.01
To specify the RA position in degrees:
funcone in.fits out.fits 23.45d 34.56 0.01
To get RA and Dec from a list but use a static value for radius (and also write
identifying info for each row in the list):
funcone -x -l list.txt in.fits out.fits MYRA MYDec 0.01
User specified columns in degrees, RA position in hours (sexagesimal notation),
Dec position in degrees (sexagesimal notation) and radius in arc minutes:
funcone -r myRa:d -d myDec in.fits out.fits 12:30:15.5 30:12 15'
SEE ALSO¶
See
funtools(7) for a list of Funtools help pages