NAME¶
setpci - configure PCI devices
SYNOPSIS¶
setpci [
options]
devices operations...
DESCRIPTION¶
setpci is a utility for querying and configuring PCI devices.
All numbers are entered in hexadecimal notation.
Root privileges are necessary for almost all operations, excluding reads of the
standard header of the configuration space on some operating systems. Please
see
lspci(8) for details on access rights.
OPTIONS¶
General options¶
- -v
- Tells setpci to be verbose and display detailed
information about configuration space accesses.
- -f
- Tells setpci not to complain when there's nothing to
do (when no devices are selected). This option is intended for use in
widely-distributed configuration scripts where it's uncertain whether the
device in question is present in the machine or not.
- -D
- `Demo mode' -- don't write anything to the configuration
registers. It's useful to try setpci -vD to verify that your
complex sequence of setpci operations does what you think it should
do.
- --version
- Show setpci version. This option should be used
stand-alone.
- --help
- Show detailed help on available options. This option should
be used stand-alone.
- --dumpregs
- Show a list of all known PCI registers and capabilities.
This option should be used stand-alone.
PCI access options¶
The PCI utilities use the PCI library to talk to PCI devices (see
pcilib(7) for details). You can use the following options to influence
its behavior:
- -A <method>
- The library supports a variety of methods to access the PCI
hardware. By default, it uses the first access method available, but you
can use this option to override this decision. See -A help for a
list of available methods and their descriptions.
- -O <param>=<value>
- The behavior of the library is controlled by several named
parameters. This option allows to set the value of any of the parameters.
Use -O help for a list of known parameters and their default
values.
- -H1
- Use direct hardware access via Intel configuration
mechanism 1. (This is a shorthand for -A intel-conf1.)
- -H2
- Use direct hardware access via Intel configuration
mechanism 2. (This is a shorthand for -A intel-conf2.)
- -G
- Increase debug level of the library.
DEVICE SELECTION¶
Before each sequence of operations you need to select which devices you wish
that operation to affect.
- -s
[[[[<domain>]:]<bus>]:][<slot>][.[<func>]]
- Consider only devices in the specified domain (in case your
machine has several host bridges, they can either share a common bus
number space or each of them can address a PCI domain of its own; domains
are numbered from 0 to ffff), bus (0 to ff), slot (0 to 1f) and function
(0 to 7). Each component of the device address can be omitted or set to
"*", both meaning "any value". All numbers are
hexadecimal. E.g., "0:" means all devices on bus 0,
"0" means all functions of device 0 on any bus, "0.3"
selects third function of device 0 on all buses and ".4" matches
only the fourth function of each device.
- -d [<vendor>]:[<device>]
- Select devices with specified vendor and device ID. Both
ID's are given in hexadecimal and may be omitted or given as
"*", both meaning "any value".
When
-s and
-d are combined, only devices that match both criteria
are selected. When multiple options of the same kind are specified, the
rightmost one overrides the others.
OPERATIONS¶
There are two kinds of operations: reads and writes. To read a register, just
specify its name. Writes have the form
name=
value,
value... where each
value is either a
hexadecimal number or an expression of type
data:
mask where both
data and
mask are hexadecimal numbers. In the latter case, only
the bits corresponding to binary ones in the
mask are changed
(technically, this is a read-modify-write operation).
There are several ways how to identity a register:
- •
- Tell its address in hexadecimal.
- •
- Spell its name. Setpci knows the names of all registers in
the standard configuration headers. Use ` setpci --dumpregs' to get
the complete list. See PCI bus specifications for the precise meaning of
these registers or consult header.h or
/usr/include/pci/pci.h for a brief sketch.
- •
- If the register is a part of a PCI capability, you can
specify the name of the capability to get the address of its first
register. See the names starting with `CAP_' or `ECAP_' in the
--dumpregs output.
- •
- If the name of the capability is not known to
setpci, you can refer to it by its number in the form CAP id
or ECAP id, where id is the numeric identifier of the
capability in hexadecimal.
- •
- Each of the previous formats can be followed by
+offset to add an offset (a hex number) to the address. This
feature can be useful for addressing of registers living within a
capability, or to modify parts of standard registers.
- •
- Finally, you should append a width specifier .B,
.W, or .L to choose how many bytes (1, 2, or 4) should be
transferred. The width can be omitted if you are referring to a register
by its name and the width of the register is well known.
All names of registers and width specifiers are case-insensitive.
EXAMPLES¶
- COMMAND
- asks for the word-sized command register.
- 4.w
- is a numeric address of the same register.
- COMMAND.l
- asks for a 32-bit word starting at the location of the
command register, i.e., the command and status registers together.
- VENDOR_ID+1.b
- specifies the upper byte of the vendor ID register
(remember, PCI is little-endian).
- CAP_PM+2.w
- corresponds to the second word of the power management
capability.
- ECAP108.l
- asks for the first 32-bit word of the extended capability
with ID 0x108.
SEE ALSO¶
lspci(8),
pcilib(7)
AUTHOR¶
The PCI Utilities are maintained by Martin Mares <mj@ucw.cz>.