'\" t .\" Copyright (c) Michael Haardt (michael@cantor.informatik.rwth-aachen.de), .\" Sun Jan 15 19:16:33 1995 .\" .\" This is free documentation; you can redistribute it and/or .\" modify it under the terms of the GNU General Public License as .\" published by the Free Software Foundation; either version 2 of .\" the License, or (at your option) any later version. .\" .\" The GNU General Public License's references to "object code" .\" and "executables" are to be interpreted as the output of any .\" document formatting or typesetting system, including .\" intermediate and printed output. .\" .\" This manual is distributed in the hope that it will be useful, .\" but WITHOUT ANY WARRANTY; without even the implied warranty of .\" MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the .\" GNU General Public License for more details. .\" .\" You should have received a copy of the GNU General Public .\" License along with this manual; if not, write to the Free .\" Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111, .\" USA. .\" .\" Modified, Sun Feb 26 15:02:58 1995, faith@cs.unc.edu .TH LP 4 1995-01-15 "Linux" "Linux Programmer's Manual" .SH NAME lp \- line printer devices .SH SYNOPSIS .B #include .SH CONFIGURATION \fBlp\fP[0\(en2] are character devices for the parallel line printers; they have major number 6 and minor number 0\(en2. The minor numbers correspond to the printer port base addresses 0x03bc, 0x0378 and 0x0278. Usually they have mode 220 and are owned by root and group lp. You can use printer ports either with polling or with interrupts. Interrupts are recommended when high traffic is expected, for example, for laser printers. For usual dot matrix printers polling will usually be enough. The default is polling. .SH DESCRIPTION The following .BR ioctl (2) calls are supported: .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPTIME, int \fP\fIarg\fP\fB)\fP" Sets the amount of time that the driver sleeps before rechecking the printer when the printer's buffer appears to be filled to \fIarg\fP. If you have a fast printer, decrease this number; if you have a slow printer then increase it. This is in hundredths of a second, the default 2 being 0.02 seconds. It only influences the polling driver. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPCHAR, int \fP\fIarg\fP\fB)\fP" Sets the maximum number of busy-wait iterations which the polling driver does while waiting for the printer to get ready for receiving a character to \fIarg\fP. If printing is too slow, increase this number; if the system gets too slow, decrease this number. The default is 1000. It only influences the polling driver. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPABORT, int \fP\fIarg\fP\fB)\fP" If \fIarg\fP is 0, the printer driver will retry on errors, otherwise it will abort. The default is 0. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPABORTOPEN, int \fP\fIarg\fP\fB)\fP" If \fIarg\fP is 0, .BR open (2) will be aborted on error, otherwise error will be ignored. The default is to ignore it. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPCAREFUL, int \fP\fIarg\fP\fB)\fP" If \fIarg\fP is 0, then the out-of-paper, offline and error signals are required to be false on all writes, otherwise they are ignored. The default is to ignore them. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPWAIT, int \fP\fIarg\fP\fB)\fP" Sets the number of busy waiting iterations to wait before strobing the printer to accept a just-written character, and the number of iterations to wait before turning the strobe off again, to \fIarg\fP. The specification says this time should be 0.5 microseconds, but experience has shown the delay caused by the code is already enough. For that reason, the default value is 0. This is used for both the polling and the interrupt driver. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPSETIRQ, int \fP\fIarg\fP\fB)\fP" This .BR ioctl (2) requires superuser privileges. It takes an .I int containing the new IRQ as argument. As a side effect, the printer will be reset. When \fIarg\fP is 0, the polling driver will be used, which is also default. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPGETIRQ, int *\fP\fIarg\fP\fB)\fP" Stores the currently used IRQ in \fIarg\fP. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPGETSTATUS, int *\fP\fIarg\fP\fB)\fP" Stores the value of the status port in \fIarg\fP. The bits have the following meaning: .TS l l. LP_PBUSY inverted busy input, active high LP_PACK unchanged acknowledge input, active low LP_POUTPA unchanged out-of-paper input, active high LP_PSELECD unchanged selected input, active high LP_PERRORP unchanged error input, active low .TE .sp Refer to your printer manual for the meaning of the signals. Note that undocumented bits may also be set, depending on your printer. .IP "\fBint ioctl(int \fP\fIfd\fP\fB, LPRESET)\fP" Resets the printer. No argument is used. .SH FILES /dev/lp* .\" .SH AUTHORS .\" The printer driver was originally written by Jim Weigand and Linus .\" Torvalds. .\" It was further improved by Michael K.\& Johnson. .\" The interrupt code was written by Nigel Gamble. .\" Alan Cox modularized it. .\" LPCAREFUL, LPABORT, LPGETSTATUS were added by Chris Metcalf. .SH "SEE ALSO" .BR chmod (1), .BR chown (1), .BR mknod (1), .BR lpcntl (8), .BR tunelp (8) .SH COLOPHON This page is part of release 3.44 of the Linux .I man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/.