other versions
- wheezy 3.44-1
- jessie 3.74-1
- jessie-backports 4.10-2~bpo8+1
- testing 4.10-2
- unstable 4.10-2
other languages
other sections
ARP(7) | Linux Programmer's Manual | ARP(7) |
NAME¶
arp - Linux ARP kernel module.DESCRIPTION¶
This kernel protocol module implements the Address Resolution Protocol defined in RFC 826. It is used to convert between Layer2 hardware addresses and IPv4 protocol addresses on directly connected networks. The user normally doesn't interact directly with this module except to configure it; instead it provides a service for other protocols in the kernel.Ioctls¶
Three ioctls are available on all AF_INET sockets. They take a pointer to a struct arpreq as their argument.struct arpreq { struct sockaddr arp_pa; /* protocol address */ struct sockaddr arp_ha; /* hardware address */ int arp_flags; /* flags */ struct sockaddr arp_netmask; /* netmask of protocol address */ char arp_dev[16]; };
arp_flags | |
flag | meaning |
ATF_COM | Lookup complete |
ATF_PERM | Permanent entry |
ATF_PUBL | Publish entry |
ATF_USETRAILERS | Trailers requested |
ATF_NETMASK | Use a netmask |
ATF_DONTPUB | Don't answer |
/proc interfaces¶
ARP supports a range of /proc interfaces to configure parameters on a global or per-interface basis. The interfaces can be accessed by reading or writing the /proc/sys/net/ipv4/neigh/*/* files. Each interface in the system has its own directory in /proc/sys/net/ipv4/neigh/. The setting in the "default" directory is used for all newly created devices. Unless otherwise specified, time-related interfaces are specified in seconds.- anycast_delay (since Linux 2.2)
- The maximum number of jiffies to delay before replying to a IPv6 neighbor solicitation message. Anycast support is not yet implemented. Defaults to 1 second.
- app_solicit (since Linux 2.2)
- The maximum number of probes to send to the user space ARP daemon via netlink before dropping back to multicast probes (see mcast_solicit). Defaults to 0.
- base_reachable_time (since Linux 2.2)
- Once a neighbor has been found, the entry is considered to be valid for at least a random value between base_reachable_time/2 and 3*base_reachable_time/2. An entry's validity will be extended if it receives positive feedback from higher level protocols. Defaults to 30 seconds. This file is now obsolete in favor of base_reachable_time_ms.
- base_reachable_time_ms (since Linux 2.6.12)
- As for base_reachable_time, but measures time in milliseconds. Defaults to 30000 milliseconds.
- delay_first_probe_time (since Linux 2.2)
- Delay before first probe after it has been decided that a neighbor is stale. Defaults to 5 seconds.
- gc_interval (since Linux 2.2)
- How frequently the garbage collector for neighbor entries should attempt to run. Defaults to 30 seconds.
- gc_stale_time (since Linux 2.2)
- Determines how often to check for stale neighbor entries. When a neighbor entry is considered stale, it is resolved again before sending data to it. Defaults to 60 seconds.
- gc_thresh1 (since Linux 2.2)
- The minimum number of entries to keep in the ARP cache. The garbage collector will not run if there are fewer than this number of entries in the cache. Defaults to 128.
- gc_thresh2 (since Linux 2.2)
- The soft maximum number of entries to keep in the ARP cache. The garbage collector will allow the number of entries to exceed this for 5 seconds before collection will be performed. Defaults to 512.
- gc_thresh3 (since Linux 2.2)
- The hard maximum number of entries to keep in the ARP cache. The garbage collector will always run if there are more than this number of entries in the cache. Defaults to 1024.
- locktime (since Linux 2.2)
- The minimum number of jiffies to keep an ARP entry in the cache. This prevents ARP cache thrashing if there is more than one potential mapping (generally due to network misconfiguration). Defaults to 1 second.
- mcast_solicit (since Linux 2.2)
- The maximum number of attempts to resolve an address by multicast/broadcast before marking the entry as unreachable. Defaults to 3.
- proxy_delay (since Linux 2.2)
- When an ARP request for a known proxy-ARP address is received, delay up to proxy_delay jiffies before replying. This is used to prevent network flooding in some cases. Defaults to 0.8 seconds.
- proxy_qlen (since Linux 2.2)
- The maximum number of packets which may be queued to proxy-ARP addresses. Defaults to 64.
- retrans_time (since Linux 2.2)
- The number of jiffies to delay before retransmitting a request. Defaults to 1 second. This file is now obsolete in favor of retrans_time_ms.
- retrans_time_ms (since Linux 2.6.12)
- The number of milliseconds to delay before retransmitting a request. Defaults to 1000 milliseconds.
- ucast_solicit (since Linux 2.2)
- The maximum number of attempts to send unicast probes before asking the ARP daemon (see app_solicit). Defaults to 3.
- unres_qlen (since Linux 2.2)
- The maximum number of packets which may be queued for each unresolved address by other network layers. Defaults to 3.
VERSIONS¶
The struct arpreq changed in Linux 2.0 to include the arp_dev member and the ioctl numbers changed at the same time. Support for the old ioctls was dropped in Linux 2.2.BUGS¶
Some timer settings are specified in jiffies, which is architecture- and kernel version-dependent; see time(7).SEE ALSO¶
capabilities(7), ip(7) RFC 826 for a description of ARP. RFC 2461 for a description of IPv6 neighbor discovery and the base algorithms used. Linux 2.2+ IPv4 ARP uses the IPv6 algorithms when applicable.COLOPHON¶
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/.2008-11-25 | Linux |