NAME¶
SIFTR —
Statistical Information For TCP
Research
SYNOPSIS¶
To load
SIFTR as a module at run-time, run the following
command as root:
Alternatively, to load
SIFTR as a module at boot time, add the
following line into the
loader.conf(5) file:
DESCRIPTION¶
SIFTR (
Statistical
Information
For
TCP
Research) is a kernel module that logs a range of statistics
on active TCP connections to a log file. It provides the ability to make
highly granular measurements of TCP connection state, aimed at system
administrators, developers and researchers.
Compile-time Configuration¶
The default operation of
SIFTR is to capture IPv4 TCP/IP
packets.
SIFTR can be configured to support IPv4 and IPv6 by
uncommenting:
in ⟨sys/modules/siftr/Makefile⟩ and recompiling.
In the IPv4-only (default) mode, standard dotted decimal notation (e.g.
"136.186.229.95") is used to format IPv4 addresses for logging. In
IPv6 mode, standard dotted decimal notation is used to format IPv4 addresses,
and standard colon-separated hex notation (see RFC 4291) is used to format
IPv6 addresses for logging. Note that SIFTR uses uncompressed notation to
format IPv6 addresses. For example, the address
"fe80::20f:feff:fea2:531b" would be logged as
"fe80:0:0:0:20f:feff:fea2:531b".
Run-time Configuration¶
SIFTR utilises the
sysctl(8) interface to
export its configuration variables to user-space. The following variables are
available:
- net.inet.siftr.enabled
- controls whether the module performs its measurements or
not. By default, the value is set to 0, which means the module will not be
taking any measurements. Having the module loaded with
net.inet.siftr.enabled set to 0 will have no impact
on the performance of the network stack, as the packet filtering hooks are
only inserted when net.inet.siftr.enabled is set to
1.
- net.inet.siftr.ppl
- controls how many inbound/outbound packets for a given TCP
connection will cause a log message to be generated for the connection. By
default, the value is set to 1, which means the module will log a message
for every packet of every TCP connection. The value can be set to any
integer in the range [1,2^32], and can be changed at any time, even while
the module is enabled.
- net.inet.siftr.logfile
- controls the path to the file that the module writes its
log messages to. By default, the file /var/log/siftr.log is used. The path
can be changed at any time, even while the module is enabled.
- net.inet.siftr.genhashes
- controls whether a hash is generated for each TCP packet
seen by SIFTR. By default, the value is set to 0, which
means no hashes are generated. The hashes are useful to correlate which
TCP packet triggered the generation of a particular log message, but
calculating them adds additional computational overhead into the fast
path.
A typical
SIFTR log file will contain 3 different types of log
message. All messages are written in plain ASCII text.
Note: The “\” present in the example log messages in this section
indicates a line continuation and is not part of the actual log message
The first type of log message is written to the file when the module is enabled
and starts collecting data from the running kernel. The text below shows an
example module enable log. The fields are tab delimited key-value pairs which
describe some basic information about the system.
enable_time_secs=1238556193 enable_time_usecs=462104 \
siftrver=1.2.2 hz=1000 tcp_rtt_scale=32 \
sysname=FreeBSD sysver=604000 ipmode=4
Field descriptions are as follows:
- enable_time_secs
- time at which the module was enabled, in seconds since the
UNIX epoch.
- enable_time_usecs
- time at which the module was enabled, in microseconds since
enable_time_secs.
- siftrver
- version of SIFTR.
- hz
- tick rate of the kernel in ticks per second.
- tcp_rtt_scale
- smoothed RTT estimate scaling factor
- sysname
- operating system name
- sysver
- operating system version
- ipmode
- IP mode as defined at compile time. An ipmode of
"4" means IPv6 is not supported and IP addresses are logged in
regular dotted quad format. An ipmode of "6" means IPv6 is
supported, and IP addresses are logged in dotted quad or hex format, as
described in the “Compile-time Configuration” subsection.
The second type of log message is written to the file when a data log message is
generated. The text below shows an example data log triggered by an IPv4
TCP/IP packet. The data is CSV formatted.
o,0xbec491a5,1238556193.463551,172.16.7.28,22,172.16.2.5,55931, \
1073725440,172312,6144,66560,66608,8,1,4,1448,936,1,996,255, \
33304,208,66608,0,208,0
Field descriptions are as follows:
- 1
- Direction of packet that triggered the log message. Either
“i” for in, or “o” for out.
- 2
- Hash of the packet that triggered the log message.
- 3
- Time at which the packet that triggered the log message was
processed by the pfil(9) hook function, in seconds and
microseconds since the UNIX epoch.
- 4
- The IPv4 or IPv6 address of the local host, in dotted quad
(IPv4 packet) or colon-separated hex (IPv6 packet) notation.
- 5
- The TCP port that the local host is communicating via.
- 6
- The IPv4 or IPv6 address of the foreign host, in dotted
quad (IPv4 packet) or colon-separated hex (IPv6 packet) notation.
- 7
- The TCP port that the foreign host is communicating
via.
- 8
- The slow start threshold for the flow, in bytes.
- 9
- The current congestion window for the flow, in bytes.
- 10
- The current bandwidth-controlled window for the flow, in
bytes.
- 11
- The current sending window for the flow, in bytes. The post
scaled value is reported, except during the initial handshake (first few
packets), during which time the unscaled value is reported.
- 12
- The current receive window for the flow, in bytes. The post
scaled value is always reported.
- 13
- The current window scaling factor for the sending
window.
- 14
- The current window scaling factor for the receiving
window.
- 15
- The current state of the TCP finite state machine, as
defined in ⟨netinet/tcp_fsm.h⟩.
- 16
- The maximum segment size for the flow, in bytes.
- 17
- The current smoothed RTT estimate for the flow, in units of
TCP_RTT_SCALE * HZ, where TCP_RTT_SCALE is a define found in tcp_var.h,
and HZ is the kernel's tick timer. Divide by TCP_RTT_SCALE * HZ to get the
RTT in secs. TCP_RTT_SCALE and HZ are reported in the enable log
message.
- 18
- SACK enabled indicator. 1 if SACK enabled, 0
otherwise.
- 19
- The current state of the TCP flags for the flow. See
⟨netinet/tcp_var.h⟩ for information about
the various flags.
- 20
- The current retransmission timeout length for the flow, in
units of HZ, where HZ is the kernel's tick timer. Divide by HZ to get the
timeout length in seconds. HZ is reported in the enable log message.
- 21
- The current size of the socket send buffer in bytes.
- 22
- The current number of bytes in the socket send buffer.
- 23
- The current size of the socket receive buffer in
bytes.
- 24
- The current number of bytes in the socket receive
buffer.
- 25
- The current number of unacknowledged bytes in-flight. Bytes
acknowledged via SACK are not excluded from this count.
- 26
- The current number of segments in the reassembly
queue.
The third type of log message is written to the file when the module is disabled
and ceases collecting data from the running kernel. The text below shows an
example module disable log. The fields are tab delimited key-value pairs which
provide statistics about operations since the module was most recently
enabled.
disable_time_secs=1238556197 disable_time_usecs=933607 \
num_inbound_tcp_pkts=356 num_outbound_tcp_pkts=627 \
total_tcp_pkts=983 num_inbound_skipped_pkts_malloc=0 \
num_outbound_skipped_pkts_malloc=0 num_inbound_skipped_pkts_mtx=0 \
num_outbound_skipped_pkts_mtx=0 num_inbound_skipped_pkts_tcb=0 \
num_outbound_skipped_pkts_tcb=0 num_inbound_skipped_pkts_icb=0 \
num_outbound_skipped_pkts_icb=0 total_skipped_tcp_pkts=0 \
flow_list=172.16.7.28;22-172.16.2.5;55931,
Field descriptions are as follows:
- disable_time_secs
- Time at which the module was disabled, in seconds since the
UNIX epoch.
- disable_time_usecs
- Time at which the module was disabled, in microseconds
since disable_time_secs.
- num_inbound_tcp_pkts
- Number of TCP packets that traversed up the network stack.
This only includes inbound TCP packets during the periods when
SIFTR was enabled.
- num_outbound_tcp_pkts
- Number of TCP packets that traversed down the network
stack. This only includes outbound TCP packets during the periods when
SIFTR was enabled.
- total_tcp_pkts
- The summation of num_inbound_tcp_pkts and
num_outbound_tcp_pkts.
- num_inbound_skipped_pkts_malloc
- Number of inbound packets that were not processed because
of failed malloc() calls.
- num_outbound_skipped_pkts_malloc
- Number of outbound packets that were not processed because
of failed malloc() calls.
- num_inbound_skipped_pkts_mtx
- Number of inbound packets that were not processed because
of failure to add the packet to the packet processing queue.
- num_outbound_skipped_pkts_mtx
- Number of outbound packets that were not processed because
of failure to add the packet to the packet processing queue.
- num_inbound_skipped_pkts_tcb
- Number of inbound packets that were not processed because
of failure to find the TCP control block associated with the packet.
- num_outbound_skipped_pkts_tcb
- Number of outbound packets that were not processed because
of failure to find the TCP control block associated with the packet.
- num_inbound_skipped_pkts_icb
- Number of inbound packets that were not processed because
of failure to find the IP control block associated with the packet.
- num_outbound_skipped_pkts_icb
- Number of outbound packets that were not processed because
of failure to find the IP control block associated with the packet.
- total_skipped_tcp_pkts
- The summation of all skipped packet counters.
- flow_list
- A CSV list of TCP flows that triggered data log messages to
be generated since the module was loaded. Each flow entry in the CSV list
is formatted as “local_ip;local_port-foreign_ip;foreign_port”.
If there are no entries in the list (i.e. no data log messages were
generated), the value will be blank. If there is at least one entry in the
list, a trailing comma will always be present.
The total number of data log messages found in the log file for a module
enable/disable cycle should equate to total_tcp_pkts - total_skipped_tcp_pkts.
IMPLEMENTATION NOTES¶
SIFTR hooks into the network stack using the
pfil(9) interface. In its current incarnation, it hooks into
the AF_INET/AF_INET6 (IPv4/IPv6)
pfil(9) filtering points,
which means it sees packets at the IP layer of the network stack. This means
that TCP packets inbound to the stack are intercepted before they have been
processed by the TCP layer. Packets outbound from the stack are intercepted
after they have been processed by the TCP layer.
The diagram below illustrates how
SIFTR inserts itself into
the stack.
----------------------------------
Upper Layers
----------------------------------
^ |
| |
| |
| v
TCP in TCP out
----------------------------------
^ |
|________ _________|
| |
| v
---------
| SIFTR |
---------
^ |
________| |__________
| |
| v
IPv{4/6} in IPv{4/6} out
----------------------------------
^ |
| |
| v
Layer 2 in Layer 2 out
----------------------------------
Physical Layer
----------------------------------
SIFTR uses the
alq(9) interface to manage
writing data to disk.
At first glance, you might mistakenly think that
SIFTR
extracts information from individual TCP packets. This is not the case.
SIFTR uses TCP packet events (inbound and outbound) for each
TCP flow originating from the system to trigger a dump of the state of the TCP
control block for that flow. With the PPL set to 1, we are in effect sampling
each TCP flow's control block state as frequently as flow packets enter/leave
the system. For example, setting PPL to 2 halves the sampling rate i.e. every
second flow packet (inbound OR outbound) causes a dump of the control block
state.
The distinction between interrogating individual packets vs interrogating the
control block is important, because
SIFTR does not remove
the need for packet capturing tools like
tcpdump(1).
SIFTR allows you to correlate and observe the
cause-and-affect relationship between what you see on the wire (captured using
a tool like
tcpdump(1)) and changes in the TCP control block
corresponding to the flow of interest. It is therefore useful to use
SIFTR and a tool like
tcpdump(1) to gather
the necessary data to piece together the complete picture. Use of either tool
on its own will not be able to provide all of the necessary data.
As a result of needing to interrogate the TCP control block, certain packets
during the lifecycle of a connection are unable to trigger a
SIFTR log message. The initial handshake takes place without
the existence of a control block and the final ACK is exchanged when the
connection is in the TIMEWAIT state.
SIFTR was designed to minimise the delay introduced to packets
traversing the network stack. This design called for a highly optimised and
minimal hook function that extracted the minimal details necessary whilst
holding the packet up, and passing these details to another thread for actual
processing and logging.
This multithreaded design does introduce some contention issues when accessing
the data structure shared between the threads of operation. When the hook
function tries to place details in the structure, it must first acquire an
exclusive lock. Likewise, when the processing thread tries to read details
from the structure, it must also acquire an exclusive lock to do so. If one
thread holds the lock, the other must wait before it can obtain it. This does
introduce some additional bounded delay into the kernel's packet processing
code path.
In some cases (e.g. low memory, connection termination), TCP packets that enter
the
SIFTR pfil(9) hook function will not
trigger a log message to be generated.
SIFTR refers to this
outcome as a “skipped packet”. Note that
SIFTR
always ensures that packets are allowed to continue through the stack, even if
they could not successfully trigger a data log message.
SIFTR will therefore not introduce any packet loss for
TCP/IP packets traversing the network stack.
Important Behaviours¶
The behaviour of a log file path change whilst the module is enabled is as
follows:
- Attempt to open the new file path for writing. If this
fails, the path change will fail and the existing path will continue to be
used.
- Assuming the new path is valid and opened successfully:
- Flush all pending log messages to the old file
path.
- Close the old file path.
- Switch the active log file pointer to point at the new
file path.
- Commence logging to the new file.
During the time between the flush of pending log messages to the old file and
commencing logging to the new file, new log messages will still be generated
and buffered. As soon as the new file path is ready for writing, the
accumulated log messages will be written out to the file.
EXAMPLES¶
To enable the module's operations, run the following command as root: sysctl
net.inet.siftr.enabled=1
To change the granularity of log messages such that 1 log message is generated
for every 10 TCP packets per connection, run the following command as root:
sysctl net.inet.siftr.ppl=10
To change the log file location to /tmp/siftr.log, run the following command as
root: sysctl net.inet.siftr.logfile=/tmp/siftr.log
SEE ALSO¶
alq(9),
pfil(9) sysctl(8),
tcp(4),
tcpdump(1),
ACKNOWLEDGEMENTS¶
Development of this software was made possible in part by grants from the Cisco
University Research Program Fund at Community Foundation Silicon Valley, and
the FreeBSD Foundation.
HISTORY¶
SIFTR first appeared in
FreeBSD 7.4
and
FreeBSD 8.2.
SIFTR was first released in 2007 by Lawrence Stewart and James
Healy whilst working on the NewTCP research project at Swinburne University's
Centre for Advanced Internet Architectures, Melbourne, Australia, which was
made possible in part by a grant from the Cisco University Research Program
Fund at Community Foundation Silicon Valley. More details are available at:
http://caia.swin.edu.au/urp/newtcp/
Work on
SIFTR v1.2.x was sponsored by the FreeBSD Foundation
as part of the “Enhancing the FreeBSD TCP Implementation” project
2008-2009. More details are available at:
http://www.freebsdfoundation.org/
http://caia.swin.edu.au/freebsd/etcp09/
AUTHORS¶
SIFTR was written by
Lawrence Stewart
⟨lstewart@FreeBSD.org⟩ and
James Healy
⟨jimmy@deefa.com⟩.
This manual page was written by
Lawrence Stewart
⟨lstewart@FreeBSD.org⟩.
BUGS¶
Current known limitations and any relevant workarounds are outlined below:
- The internal queue used to pass information between the
threads of operation is currently unbounded. This allows
SIFTR to cope with bursty network traffic, but sustained
high packet-per-second traffic can cause exhaustion of kernel memory if
the processing thread cannot keep up with the packet rate.
- If using SIFTR on a machine that is also
running other modules utilising the pfil(9) framework
e.g. dummynet(4), ipfw(8),
pf(4), the order in which you load the modules is
important. You should kldload the other modules first, as this will ensure
TCP packets undergo any necessary manipulations before
SIFTR “sees” and processes them.
- There is a known, harmless lock order reversal warning
between the pfil(9) mutex and tcbinfo TCP lock reported
by witness(4) when SIFTR is enabled in
a kernel compiled with witness(4) support.
- There is no way to filter which TCP flows you wish to
capture data for. Post processing is required to separate out data
belonging to particular flows of interest.
- The module does not detect deletion of the log file path.
New log messages will simply be lost if the log file being used by
SIFTR is deleted whilst the module is set to use the
file. Switching to a new log file using the
net.inet.siftr.logfile variable will create the new file
and allow log messages to begin being written to disk again. The new log
file path must differ from the path to the deleted file.
- The hash table used within the code is sized to hold 65536
flows. This is not a hard limit, because chaining is used to handle
collisions within the hash table structure. However, we suspect (based on
analogies with other hash table performance data) that the hash table look
up performance (and therefore the module's packet processing performance)
will degrade in an exponential manner as the number of unique flows
handled in a module enable/disable cycle approaches and surpasses
65536.
- There is no garbage collection performed on the flow hash
table. The only way currently to flush it is to disable
SIFTR.
- The PPL variable applies to packets that make it into the
processing thread, not total packets received in the hook function.
Packets are skipped before the PPL variable is applied, which means there
may be a slight discrepancy in the triggering of log messages. For
example, if PPL was set to 10, and the 8th packet since the last log
message is skipped, the 11th packet will actually trigger the log message
to be generated. This is discussed in greater depth in CAIA technical
report 070824A.
- At the time of writing, there was no simple way to hook
into the TCP layer to intercept packets. SIFTR's use of
IP layer hook points means all IP traffic will be processed by the
SIFTR pfil(9) hook function, which
introduces minor, but nonetheless unnecessary packet delay and processing
overhead on the system for non-TCP packets as well. Hooking in at the IP
layer is also not ideal from the data gathering point of view. Packets
traversing up the stack will be intercepted and cause a log message
generation BEFORE they have been processed by the TCP layer, which means
we cannot observe the cause-and-affect relationship between inbound events
and the corresponding TCP control block as precisely as could be. Ideally,
SIFTR should intercept packets after they have been
processed by the TCP layer i.e. intercept packets coming up the stack
after they have been processed by tcp_input(), and intercept packets
coming down the stack after they have been processed by tcp_output(). The
current code still gives satisfactory granularity though, as inbound
events tend to trigger outbound events, allowing the cause-and-effect to
be observed indirectly by capturing the state on outbound events as
well.
- The “inflight bytes” value logged by
SIFTR does not take into account bytes that have been
SACK'ed by the receiving host.
- Packet hash generation does not currently work for IPv6
based TCP packets.
- Compressed notation is not used for IPv6 address
representation. This consumes more bytes than is necessary in log
output.