Scroll to navigation

SS-SERVER(1) Shadowsocks-libev Manual SS-SERVER(1)

NAME

ss-server - shadowsocks server, libev port

SYNOPSIS

ss-server [-uUv] [-h|--help] [-s <server_host>] [-p <server_port>] [-l <local_port>] [-k <password>] [-m <encrypt_method>] [-f <pid_file>] [-t <timeout>] [-c <config_file>] [-i <interface>] [-a <user_name>] [-d <addr>] [-n <nofile>] [-b <local_address>] [--fast-open] [--reuse-port] [--mptcp] [--acl <acl_config>] [--mtu <MTU>] [--no-delay] [--manager-address <path_to_unix_domain>] [--plugin <plugin_name>] [--plugin-opts <plugin_options>] [--password <password>] [--key <key_in_base64>]

DESCRIPTION

Shadowsocks-libev is a lightweight and secure socks5 proxy. It is a port of the original shadowsocks created by clowwindy. Shadowsocks-libev is written in pure C and takes advantage of libev to achieve both high performance and low resource consumption.

Shadowsocks-libev consists of five components. ss-server(1) runs on a remote server to provide secured tunnel service. For more information, check out shadowsocks-libev(8).

OPTIONS

-s <server_host>

Set the server’s hostname or IP.

-p <server_port>

Set the server’s port number.

-k <password>, --password <password>

Set the password. The server and the client should use the same password.

--key <key_in_base64>

Set the key directly. The key should be encoded with URL-safe Base64.

-m <encrypt_method>

Set the cipher.

Shadowsocks-libev accepts 19 different ciphers:

aes-128-gcm, aes-192-gcm, aes-256-gcm, rc4-md5, aes-128-cfb, aes-192-cfb, aes-256-cfb, aes-128-ctr, aes-192-ctr, aes-256-ctr, bf-cfb, camellia-128-cfb, camellia-192-cfb, camellia-256-cfb, chacha20-ietf-poly1305, xchacha20-ietf-poly1305, salsa20, chacha20 and chacha20-ietf.

If built with PolarSSL or custom OpenSSL libraries, some of these ciphers may not work.

-a <user_name>

Run as a specific user.

-f <pid_file>

Start shadowsocks as a daemon with specific pid file.

-t <timeout>

Set the socket timeout in seconds. The default value is 60.

-c <config_file>

Use a configuration file.

Refer to shadowsocks-libev(8) CONFIG FILE section for more details.

-n <number>

Specify max number of open files.

Only available on Linux.

-i <interface>

Send traffic through specific network interface.

For example, there are three interfaces in your device, which is lo (127.0.0.1), eth0 (192.168.0.1) and eth1 (192.168.0.2). Meanwhile, you configure ss-server to listen on 0.0.0.0:8388 and bind to eth1. That results the traffic go out through eth1, but not lo nor eth0. This option is useful to control traffic in multi-interface environment.

-b <local_address>

Specify the local address to use while this server is making outbound connections to remote servers on behalf of the clients.

-u

Enable UDP relay.

-U

Enable UDP relay and disable TCP relay.

-6

Resovle hostname to IPv6 address first.

-d <addr>

Setup name servers for internal DNS resolver (libc-ares). The default server is fetched from /etc/resolv.conf.

--fast-open

Enable TCP fast open.

Only available with Linux kernel > 3.7.0.

--reuse-port

Enable port reuse.

Only available with Linux kernel > 3.9.0.

--no-delay

Enable TCP_NODELAY.

--acl <acl_config>

Enable ACL (Access Control List) and specify config file.

--manager-address <path_to_unix_domain>

Specify UNIX domain socket address for the communication between ss-manager(1) and ss-server(1).

Only available in server and manager mode.

--mtu <MTU>

Specify the MTU of your network interface.

--mptcp

Enable Multipath TCP.

Only available with MPTCP enabled Linux kernel.

--plugin <plugin_name>

Enable SIP003 plugin. (Experimental)

--plugin-opts <plugin_options>

Set SIP003 plugin options. (Experimental)

-v

Enable verbose mode.

-h|--help

Print help message.

EXAMPLE

It is recommended to use a config file when starting ss-server(1).

The config file is written in JSON and is easy to edit. Check out the SEE ALSO section for the default path of config file.

# Start the ss-server
ss-server -c /etc/shadowsocks-libev/config.json

INCOMPATIBILITY

The config file of shadowsocks-libev(8) is slightly different from original shadowsocks.

In order to listen to both IPv4/IPv6 address, use the following grammar in your config json file:

{
"server":["::0","0.0.0.0"],
...
}

ss-server(1) also does not understand "port_password" field in config file. If you want to start up multiple server instances with a single config file, please try ss-manager tool. See ss-manager(8) for details.

SEE ALSO

ss-local(1), ss-tunnel(1), ss-redir(1), ss-manager(1), shadowsocks-libev(8), iptables(8), /etc/shadowsocks-libev/config.json

03/15/2024 Shadowsocks-libev 3.3.5