Scroll to navigation

DIVALOAD(8) Linux System Administration DIVALOAD(8)

NAME

divaload - configure Eicon Diva active ISDN card

SYNOPSIS

divaload controller protocol [options]

DESCRIPTION

divaload is used to setup the Eicon Diva card for the proper configuration.

OPTIONS

selects the controller (card). This can be either:
-c n
where n is the controller number, or
-all
to operate on all cards.

can be one of the following: 


  -f 1TR6     Germany, old protocol for PABX................ PRI & BRI


  -f ETSI     DSS1, Europe (Germany, ...)................... PRI & BRI


  -f FRANC    VN3, France, old protocol for PABX............ PRI & BRI


  -f BELG     NET3, Belgien, old protocol for PABX.......... PRI & BRI


  -f SWED     DSS1 with CRC4 off, Sweden, Benelux........... PRI


  -f NI       NI1, NI2, North America, National ISDN........ PRI & BRI


  -f 5ESS     5ESS, North America, AT&T..................... PRI & BRI


  -f JAPAN    Japan, INS-NET64.............................. PRI & BRI


  -f ATEL     ATEL, Australia, old TPH1962.................. PRI & BRI


  -f US       North America, Auto Detect....................       BRI


  -f ITALY    DSS1, Italy................................... PRI & BRI


  -f TWAN     DSS1, Taiwan.................................. PRI & BRI


  -f AUSTRAL  Australia, Microlink (TPH1962), On Ramp ETSI.. PRI & BRI


  -f 4ESS_SDN 4ESS Software Defined Network................. PRI


  -f 4ESS_SDS 4ESS Switched Digital Service................. PRI


  -f 4ESS_LDS 4ESS Long Distance Service.................... PRI


  -f 4ESS_MGC 4ESS Megacom.................................. PRI


  -f 4ESS_MGI 4ESS Megacom International.................... PRI


  -f HONGKONG Hongkong...................................... PRI & BRI


  -f RBSCAS   Robbed Bit Signaling, CAS..................... PRI


  -f QSIG     QSIG, Intra PABX link protocol................ PRI & BRI

The following options may be given to divaload.

set Layer 1 framing on PRI Adapter

1 - doubleframing (NO CRC4)
2 - multiframing (CRC4)
3 - autodetection
set PRI Adapter in NT mode; default mode is TE
set PRI Adapter in High Impedance state until first user application does request interface activation
set starting channel number on PRI Adapter. By default the allocation of channels is made on a high-to-low basis. By specifying -l you select a low-to-high allocation policy (in addition)
select QSIG options

0 - CR and CHI 2 Bytes long (default)
1 - CR 1 byte, CHI 2 bytes
2 - CR is 2 bytes, CHI is 1 byte
3 - CR and CHI 1 byte
(CR - Call Reference, CHI - B-Channel Ident.)
select NT2 mode and default length of DIDN (DIDN - Direct Inward Dial Number)
turn off order checking of information elements
establish a permanent connection (e.g. leased line configuration)

1 - TE <-> TE mode, structured line
2 - NT <-> TE mode, raw line
D-Channel Layer 2 activation policy on BRI Adapter

0 - On demand
1 - Deactivation only by NT side, preferred, default
2 - Always active
3 - Always active, mode 2

specifies a fixed TEI value (Default is a automatic TEI assignment)

select point to point mode on BRI Adapter; uses default TEI '0', NT2 mode is on

-[1...8]oad|osa|spid
BRI Adapter B-Channel options Specify the Originating Address (OAD), Originating Sub-address (OSA) and/or Service Profile Identifier (SPID) for each B-channel (1 or 2 by BRI, 1...8 by 4BRI)
Example: -1oad 123456 -1spid 1234560001

display protocol options summary

select alternative protocol code directory.
default directory: "/usr/share/isdn"

help

AUTHOR

manpage written from -h output by Paul Slootman <paul@debian.org>.

2000/12/02 divaload