|SSH-COPY-ID(1)||General Commands Manual||SSH-COPY-ID(1)|
ssh-copy-idis a script that uses ssh(1) to log into a remote machine (presumably using a login password, so password authentication should be enabled, unless you've done some clever use of multiple identities). It assembles a list of one or more fingerprints (as described below) and tries to log in with each key, to see if any of them are already installed (of course, if you are not using ssh-agent(1) this may result in you being repeatedly prompted for pass-phrases). It then assembles a list of those that failed to log in, and using ssh, enables logins with those keys on the remote server. By default it adds the keys by appending them to the remote user's ~/.ssh/authorized_keys (creating the file, and directory, if necessary). It is also capable of detecting if the remote system is a NetScreen, and using its ‘
set ssh pka-dsa key ...’ command instead.
The options are as follows:
- Use only the key(s) contained in identity_file
(rather than looking for identities via ssh-add(1) or in
default_ID_file). If the filename does not end in .pub this is added. If the filename is omitted, the
Note that this can be used to ensure that the keys copied have the comment one prefers and/or extra options applied, by ensuring that the key file has these set as preferred before the copy is attempted.
- Forced mode: doesn't check if the keys are present on the remote server. This means that it does not need the private key. Of course, this can result in more than one copy of the key being installed on the remote system.
- do a dry-run. Instead of installing keys on the remote system simply prints the key(s) that would have been installed.
- Print Usage summary
- These two options are simply passed through untouched, along with their argument, to allow one to set the port or other ssh(1) options, respectively.
Default behaviour without
-i, is to check
ssh-add -L’ provides any output,
and if so those keys are used. Note that this results in the comment on the
key being the filename that was given to ssh-add(1) when
the key was loaded into your ssh-agent(1) rather than the
comment contained in that file, which is a bit of a shame. Otherwise, if
ssh-add(1) provides no keys contents of the
default_ID_file will be used.
default_ID_file is the most recent
file that matches: ~/.ssh/id*.pub, (excluding those
that match ~/.ssh/*-cert.pub) so if you create a key
that is not the one you want
ssh-copy-id to use,
just use touch(1) on your preferred key's
.pub file to reinstate it as the most recent.
EXAMPLES¶If you have already installed keys from one system on a lot of remote hosts, and you then create a new key, on a new client machine, say, it can be difficult to keep track of which systems on which you've installed the new key. One way of dealing with this is to load both the new key and old key(s) into your ssh-agent(1). Load the new key first, without the
-coption, then load one or more old keys into the agent, possibly by ssh-ing to the client machine that has that old key, using the
-Aoption to allow agent forwarding:
now, if the new key is installed on the server, you'll be allowed in unprompted, whereas if you only have the old key(s) enabled, you'll be asked for confirmation, which is your cue to log back out and run
The reason you might want to specify the -i option in this case is to ensure that the comment on the installed key is the one from the .pub file, rather than just the filename that was loaded into your agent. It also ensures that only the id you intended is installed, rather than all the keys that you have in your ssh-agent(1). Of course, you can specify another id, or use the contents of the ssh-agent(1) as you prefer.
Having mentioned ssh-add(1)'s
-c option, you might consider using this whenever
using agent forwarding to avoid your key being hijacked, but it is much
better to instead use ssh(1)'s
-W option, to
bounce through remote servers while always doing direct end-to-end
authentication. This way the middle hop(s) don't get access to your
ssh-agent(1). A web search for
ssh proxycommand nc’ should prove
enlightening (N.B. the modern approach is to use the
-W option, rather than nc(1)).
SEE ALSO¶ssh(1), ssh-agent(1), sshd(8)
|June 17, 2010||Linux 4.19.0-10-amd64|