Scroll to navigation

LIRCD.CONF(5) File Formats Manual LIRCD.CONF(5)

NAME

lircd.conf - lirc main configuration file

DESCRIPTION

The file has two purposes: to provide timing information to the driver so it can decode the data to button presses, and to provide a mapping from button presses to key symbols used by lircd(8).

The basic structure is a list of remote blocks. Whitespace and line breaks are used as delimiters.

If the comment character (#) appears as the first character on a line the rest of the line is ignored.

REMOTE BLOCKS

Remote blocks are either normal or raw.

Normal remote blocks begin with begin remote and ends with end remote. The first part of the block describes the basic properties of the remote, see REMOTE DESCRIPTION SECTION. Following this is a codes section, which is delimited by begin codes and end codes.

Each line in a codes section contains the name of a button on the remote followed by a hexadecimal data value matching the data part of the IR frame (see REMOTE DESCRIPTION SECTION). You may not assign the same name to two buttons in the same remote section.

Raw remote blocks are identical to normal blocks besides the codes section which is a list of button descriptions enclosed by begin raw_codes and end raw_codes.

A raw button description begins with the parameter name followed by the name of the button. The button description ends with the next button description or the end of the raw_codes block. The lines in between is a list of decimal numbers describing the signal sent by that button. The first number indicates the duration of the first pulse in microseconds. The second number indicates the duration of the space which follows it. Pulse and space durations alternate for as long as is necessary. The last duration should represent a pulse.

REMOTE DESCRIPTION SECTION

Each line in this section contains a parameter followed by the value or values that should be assigned to that parameter. Parameters are optional unless otherwise stated.

All values are decimal integers that are either dimensionless or have units of microseconds unless otherwise stated. Hexadecimal numbers should be prefixed by 0x. If the remote does not have a particular "feature," then the line may be omitted. The button code is sent just after the pre signal and just before the post signal.

Some parameters describe the bits in the IR protocol. The frame is normally defined like

|header|plead|pre data|pre|data|post|post data|ptrail|foot|gap|

where most parameters defaults to 0. Some parameters change the overall frame layout e. g., the repeat parameter.

Include the given path using normal include semantics. If the path is relative, it's interpreted relative to the main lircd.conf file. <path> must be enclosed in double quotes. It can contain a glob(3) pattern in which case all matching files are included.
Normally, lircd tries to sort multiple remotes so the one which decodes fastest are used first. Setting manual_sort to 1 in any remote disables this and uses the remotes in the order they are listed in lircd.conf or as the alphanumerically sorted filenames in lircd.conf.d.
The unique name assigned to the remote control (may not contain whitespace). Within a single file all names must be unique. Parameter is mandatory.
Suppress a given number of repeats for all buttons in this remote. Defaults to 0, which means that no repeats are suppressed. Note that lircrc has a corresponding repeat parameter which can be used to suppress repeats for specific button/client combinations.
Flags are special text strings which describe various properties of the remote and determine the semantics of some of the following fields. Multiple flags should be separated by the pipe(|) symbol. See FLAGS.
For lirccode drivers which does not have timing information the optional driver attribute names the driver which is required to use this remote.
The number of data bits in the hexadecimal codes which describe each button (decimal integer).
The relative error tolerance for received signals in percent. By default, irrecord set this to 30 (i. e., 30%).
The absolute error tolerance for received signals (microseconds). The default is the hardcoded driver dependent resolution value. By default irrecord sets this to 100.
The initial pulse and space sent (microseconds).
Only used by RC-MM remotes
Only used by RC-MM remotes
The pulse and space lengths representing a one.
The pulse and space lengths representing a zero.
A trailing pulse, immediately following the post_data.
A leading pulse, immediately after the header.
A pulse and space, immediately following the trailing pulse.
A pulse and space that replaces everything between leading pulse and the trailing pulse, whenever a signal is repeated. The foot is not sent, and the header is not sent unless the REPEAT_HEADER flag is present.
The number of bits in the pre_data code.
Hexadecimal code indicating the sequence of ones and zeros immediately following the leading pulse.
The number of bits in the post_data code.
Hexadecimal code indicating the sequence of ones and zeros immediately following the post signal.
A pulse and space immediately following the pre_data.
A pulse and space immediately following the button code.
A (typically long) space which follows the trailing pulse.
A gap immediately following the trailing pulse, and preceding a repetition of the same code that's due to a the same press of the button.
The minimum times a signal is repeated when sent. Note that 0 means the signal is sent only once. Not used when receiving.
A bit of the pre_data, code, or post_data that is toggled between one and zero each time a button is pressed. This parameter is obsoleted by toggle_bit_mask and should be used in new configs.
Bits which are toggled between one and zero each time a button is pressed. The mask is applied to the concatenated value of pre data - data - post_data.
Mask defines which bits are inverted for repeats.
Remote carrier frequency, defaults to 38000.
The percentage of time during a pulse that infrared light is being sent. This is an integer between 1-100 inclusive. default is 50.

FLAGS

Flags are values set in the flags parameter.

The remote uses the RC5 protocol.
The remote uses the RC6 protocol.
The remote uses the RC-MM protocol.
Obsolete flag, now a synonym for RC5. The position of the pulse (before or after the space) determines whether the bit is a one or a zero.
A one and a zero can be distinguished by the length of the spaces, used by the NEC protocol and others.
Reverses the bit order of the pre_data, the post_data and the codes (e.g., 0x123 becomes 0xC48). If this flag is present, the least significant bit is sent first.
The header is not sent when a signal (the button is held down) is repeated even though there is no special repeat code.
The foot is not sent when a signal is repeated (the button is held down) even though there is no special repeat code .
The total signal length is always constant. The gap length now represents the length of the entire signal, and the actual gap at the end of the signal is adjusted accordingly.
The codes are in raw format.
Send the header when the signal is repeated even though the remote has a special repeat code.

DISCLAIMER

LIRC was designed to collect IR data and save it in a private, compact, yet human readable format with the purpose of being able to re-transmit (or re-recognize) these signals. It was not designed with the goal of providing a well documented and tested configuration file format that could be used e.g., to generate arbitrary IR signals or to convert them to other formats. The configuration file should thus not be considered a public interface to LIRC.

This manpage should be understood with this in mind. It was authored by reading the code of LIRC, and does not constitute an authoritative specification of the behavior of LIRC and its configuration file. Also, some less commonly used flags and parameters are not documented.

SEE ALSO

lircd(8)
irrecord(1)
http://en.wikipedia.org/wiki/RC-5
http://www.sbprojects.com/knowledge/ir/
Last change: Apr 2017 lircd.conf 0.10.1