table of contents
MBIMCLI(1) | User Commands | MBIMCLI(1) |
NAME¶
mbimcli - Control MBIM devices
DESCRIPTION¶
Usage:¶
- lt-mbimcli [OPTION?] - Control MBIM devices
Help Options:¶
- -h, --help
- Show help options
- --help-all
- Show all help options
- --help-basic-connect
- Show Basic Connect Service options
- --help-phonebook
- Show Phonebook Service options
- --help-dss
- Show Device Service Stream options
- --help-ms-firmware-id
- Show Microsoft Firmware ID Service options
- --help-ms-host-shutdown
- Show Microsoft Host Shutdown Service options
- --help-ms-sar
- Show Microsoft SAR Service options
- --help-atds
- Show AT&T Device Service options
- --help-intel-firmware-update
- Show Intel Firmware Update Service options
- --help-ms-basic-connect-extensions
- Show Microsoft Basic Connect Extensions Service options
- --help-quectel
- Show Quectel Service options
- --help-link-management
- Show link management specific options
Basic Connect options:¶
- --query-device-caps
- Query device capabilities
- --query-subscriber-ready-status
- Query subscriber ready status
- --query-radio-state
- Query radio state
- --set-radio-state=[(on|off)]
- Set radio state
- --query-device-services
- Query device services
- --query-pin-state
- Query PIN state
- --enter-pin=[(PIN type),(current PIN)]
- Enter PIN (PIN type is optional, defaults to PIN1, allowed options: (pin1,network-pin,network-subset-pin,service-provider-pin,corporate-pin)
- --change-pin=[(current PIN),(new PIN)]
- Change PIN
- --enable-pin=[(current PIN)]
- Enable PIN
- --disable-pin=[(PIN type),(current PIN)]
- Disable PIN (PIN type is optional, see enter-pin for details)
- --enter-puk=[(PUK type),(PUK),(new PIN)]
- Enter PUK (PUK type is optional, defaults to PUK1, allowed options: (puk1,network-puk,network-subset-puk,service-provider-puk,corporate-puk)
- --query-pin-list
- Query PIN list
- --query-home-provider
- Query home provider
- --query-preferred-providers
- Query preferred providers
- --query-visible-providers
- Query visible providers
- --query-registration-state
- Query registration state
- --register-automatic
- Launch automatic registration
- --query-signal-state
- Query signal state
- --query-packet-service-state
- Query packet service state
- --attach-packet-service
- Attach to the packet service
- --detach-packet-service
- Detach from the packet service
- --query-connection-state=[SessionID]
- Query connection state (SessionID is optional, defaults to 0)
- --connect=["key=value,..."]
- Connect (allowed keys: session-id, apn, ip-type (ipv4|ipv6|ipv4v6), auth (PAP|CHAP|MSCHAPV2), username, password)
- --query-ip-configuration=[SessionID]
- Query IP configuration (SessionID is optional, defaults to 0)
- --disconnect=[SessionID]
- Disconnect (SessionID is optional, defaults to 0)
- --query-packet-statistics
- Query packet statistics
- --query-ip-packet-filters=[SessionID]
- Query IP packet filters (SessionID is optional, defaults to 0)
- --query-provisioned-contexts
- Query provisioned contexts
Phonebook options:¶
- --phonebook-query-configuration
- Query the phonebook configuration
- --phonebook-read=[(Phonebook index)]
- Read phonebook entry with given index
- --phonebook-read-all
- Read all phonebook entries
- --phonebook-write=[(Name),(Number)[,(Index)]]
- Add new phonebook entry or update an existing one
- --phonebook-delete=[(Phonebook index)]
- Delete phonebook entry with given index
- --phonebook-delete-all
- Delete all phonebook entries
Device Service Stream options:¶
- --dss-connect=[(UUID),(Session ID)]
- Connect DSS session
- --dss-disconnect=[(UUID),(Session ID)]
- Disconnect DSS session
Microsoft Firmware ID options:¶
- --ms-query-firmware-id
- Query firmware ID
Microsoft Host Shutdown options:¶
- --ms-notify-host-shutdown
- Notify that host is shutting down
Microsoft SAR options:¶
- --ms-set-sar-config=[(device|os),(enabled|disabled)[,[{antenna_index,backoff_index}...]]]
- Set SAR config
- --ms-query-sar-config
- Query SAR config
- --ms-set-transmission-status=[(enabled|disabled),(timer)]
- Set transmission status and hysteresis timer (in seconds)
- --ms-query-transmission-status
- Query transmission status
AT&T Device Service options:¶
- --atds-query-signal
- Query signal info
- --atds-query-location
- Query cell location
Intel Firmware Update Service options:¶
- --intel-modem-reboot
- Reboot modem
Microsoft Basic Connect Extensions options:¶
- --ms-query-pco=[SessionID]
- Query PCO value (SessionID is optional, defaults to 0)
- --ms-query-lte-attach-configuration
- Query LTE attach configuration
- --ms-query-lte-attach-info
- Query LTE attach status information
- --ms-query-sys-caps
- Query system capabilities
- --ms-query-device-caps
- Query device capabilities
- --ms-query-slot-info-status=[SlotIndex]
- Query slot information status
- --ms-set-device-slot-mappings=[(SlotIndex)[,(SlotIndex)[,...]]]
- Set device slot mappings for each executor
- --ms-query-device-slot-mappings
- Query device slot mappings
Quectel options:¶
- --quectel-query-radio-state
- Query radio state
- --quectel-set-radio-state=[(on)]
- Set radio state
Link management options:¶
- --link-list=[IFACE]
- List links created from a given interface
- --link-add=[iface=IFACE,prefix=PREFIX[,session-id=N]]
- Create new network interface link
- --link-delete=IFACE
- Delete a given network interface link
- --link-delete-all=[IFACE]
- Delete all network interface links from the given interface
Application Options:¶
- -d, --device=[PATH]
- Specify device path
- -p, --device-open-proxy
- Request to use the 'mbim-proxy' proxy
- --no-open=[Transaction ID]
- Do not explicitly open the MBIM device before running the command
- --no-close
- Do not close the MBIM device after running the command
- --noop
- Don't run any command
- -v, --verbose
- Run action with verbose logs, including the debug ones
- --silent
- Run action with no logs; not even the error/warning ones
- -V, --version
- Print version
COPYRIGHT¶
Copyright © 2013-2021 Aleksander Morgado License GPLv2+:
GNU GPL version 2 or later <http://gnu.org/licenses/gpl-2.0.html>
This is free software: you are free to change and redistribute it. There is NO
WARRANTY, to the extent permitted by law.
SEE ALSO¶
The full documentation for mbimcli is maintained as a Texinfo manual. If the info and mbimcli programs are properly installed at your site, the command
- info mbimcli
should give you access to the complete manual.
April 2022 | mbimcli 1.26.4 |