table of contents
BPF(4) | Device Drivers Manual | BPF(4) |
NAME¶
bpf
—
SYNOPSIS¶
device bpf
DESCRIPTION¶
The Berkeley Packet Filter provides a raw interface to data link layers in a protocol independent fashion. All packets on the network, even those destined for other hosts, are accessible through this mechanism.The packet filter appears as a character special device,
/dev/bpf. After opening the device, the file
descriptor must be bound to a specific network interface with the
BIOCSETIF
ioctl. A given interface can be shared by
multiple listeners, and the filter underlying each descriptor will see an
identical packet stream.
A separate device file is required for each minor device. If a
file is in use, the open will fail and errno will be
set to EBUSY
.
Associated with each open instance of a
bpf
file is a user-settable packet filter. Whenever
a packet is received by an interface, all file descriptors listening on that
interface apply their filter. Each descriptor that accepts the packet
receives its own copy.
The packet filter will support any link level protocol that has
fixed length headers. Currently, only Ethernet, SLIP, and PPP drivers have
been modified to interact with bpf
.
Since packet data is in network byte order, applications should use the byteorder(3) macros to extract multi-byte values.
A packet can be sent out on the network by writing to a
bpf
file descriptor. The writes are unbuffered,
meaning only one packet can be processed per write. Currently, only writes
to Ethernets and SLIP links are supported.
BUFFER MODES¶
bpf
devices deliver packet data to the application via
memory buffers provided by the application. The buffer mode is set using the
BIOCSETBUFMODE
ioctl, and read using the
BIOCGETBUFMODE
ioctl.
Buffered read mode¶
By default,bpf
devices operate in the
BPF_BUFMODE_BUFFER
mode, in which packet data is
copied explicitly from kernel to user memory using the
read(2) system call. The user process will declare a fixed
buffer size that will be used both for sizing internal buffers and for all
read(2) operations on the file. This size is queried using
the BIOCGBLEN
ioctl, and is set using the
BIOCSBLEN
ioctl. Note that an individual packet larger
than the buffer size is necessarily truncated.
Zero-copy buffer mode¶
bpf
devices may also operate in the
BPF_BUFMODE_ZEROCOPY
mode, in which packet data is
written directly into two user memory buffers by the kernel, avoiding both
system call and copying overhead. Buffers are of fixed (and equal) size,
page-aligned, and an even multiple of the page size. The maximum zero-copy
buffer size is returned by the BIOCGETZMAX
ioctl. Note
that an individual packet larger than the buffer size is necessarily
truncated.
The user process registers two memory buffers using the
BIOCSETZBUF
ioctl, which accepts a
struct bpf_zbuf pointer as an argument:
struct bpf_zbuf { void *bz_bufa; void *bz_bufb; size_t bz_buflen; };
bz_bufa is a pointer to the userspace
address of the first buffer that will be filled, and
bz_bufb is a pointer to the second buffer.
bpf
will then cycle between the two buffers as they
fill and are acknowledged.
Each buffer begins with a fixed-length header to hold synchronization and data length information for the buffer:
struct bpf_zbuf_header { volatile u_int bzh_kernel_gen; /* Kernel generation number. */ volatile u_int bzh_kernel_len; /* Length of data in the buffer. */ volatile u_int bzh_user_gen; /* User generation number. */ /* ...padding for future use... */ };
The header structure of each buffer, including all padding, should
be zeroed before it is configured using BIOCSETZBUF
.
Remaining space in the buffer will be used by the kernel to store packet
data, laid out in the same format as with buffered read mode.
The kernel and the user process follow a simple acknowledgement protocol via the buffer header to synchronize access to the buffer: when the header generation numbers, bzh_kernel_gen and bzh_user_gen, hold the same value, the kernel owns the buffer, and when they differ, userspace owns the buffer.
While the kernel owns the buffer, the contents are unstable and may change asynchronously; while the user process owns the buffer, its contents are stable and will not be changed until the buffer has been acknowledged.
Initializing the buffer headers to all 0's before registering the buffer has the effect of assigning initial ownership of both buffers to the kernel. The kernel signals that a buffer has been assigned to userspace by modifying bzh_kernel_gen, and userspace acknowledges the buffer and returns it to the kernel by setting the value of bzh_user_gen to the value of bzh_kernel_gen.
In order to avoid caching and memory re-ordering effects, the user process must use atomic operations and memory barriers when checking for and acknowledging buffers:
#include <machine/atomic.h> /* * Return ownership of a buffer to the kernel for reuse. */ static void buffer_acknowledge(struct bpf_zbuf_header *bzh) { atomic_store_rel_int(&bzh->bzh_user_gen, bzh->bzh_kernel_gen); } /* * Check whether a buffer has been assigned to userspace by the kernel. * Return true if userspace owns the buffer, and false otherwise. */ static int buffer_check(struct bpf_zbuf_header *bzh) { return (bzh->bzh_user_gen != atomic_load_acq_int(&bzh->bzh_kernel_gen)); }
The user process may force the assignment of the next buffer, if
any data is pending, to userspace using the
BIOCROTZBUF
ioctl. This allows the user process to
retrieve data in a partially filled buffer before the buffer is full, such
as following a timeout; the process must recheck for buffer ownership using
the header generation numbers, as the buffer will not be assigned to
userspace if no data was present.
As in the buffered read mode, kqueue(2), poll(2), and select(2) may be used to sleep awaiting the availability of a completed buffer. They will return a readable file descriptor when ownership of the next buffer is assigned to user space.
In the current implementation, the kernel may assign zero, one, or both buffers to the user process; however, an earlier implementation maintained the invariant that at most one buffer could be assigned to the user process at a time. In order to both ensure progress and high performance, user processes should acknowledge a completely processed buffer as quickly as possible, returning it for reuse, and not block waiting on a second buffer while holding another buffer.
IOCTLS¶
The ioctl(2) command codes below are defined in<net/bpf.h>
. All commands
require these includes:
#include <sys/types.h> #include <sys/time.h> #include <sys/ioctl.h> #include <net/bpf.h>
Additionally, BIOCGETIF
and
BIOCSETIF
require
<sys/socket.h>
and
<net/if.h>
.
In addition to FIONREAD
the following
commands may be applied to any open bpf
file. The
(third) argument to ioctl(2) should be a pointer to the
type indicated.
BIOCGBLEN
- (
u_int
) Returns the required buffer length for reads onbpf
files. BIOCSBLEN
- (
u_int
) Sets the buffer length for reads onbpf
files. The buffer must be set before the file is attached to an interface withBIOCSETIF
. If the requested buffer size cannot be accommodated, the closest allowable size will be set and returned in the argument. A read call will result inEIO
if it is passed a buffer that is not this size. BIOCGDLT
- (
u_int
) Returns the type of the data link layer underlying the attached interface.EINVAL
is returned if no interface has been specified. The device types, prefixed with “DLT_
”, are defined in<net/bpf.h>
. BIOCPROMISC
- Forces the interface into promiscuous mode. All packets, not just those destined for the local host, are processed. Since more than one file can be listening on a given interface, a listener that opened its interface non-promiscuously may receive packets promiscuously. This problem can be remedied with an appropriate filter.
BIOCFLUSH
- Flushes the buffer of incoming packets, and resets the statistics that are returned by BIOCGSTATS.
BIOCGETIF
- (
struct ifreq
) Returns the name of the hardware interface that the file is listening on. The name is returned in the ifr_name field of theifreq
structure. All other fields are undefined. BIOCSETIF
- (
struct ifreq
) Sets the hardware interface associate with the file. This command must be performed before any packets can be read. The device is indicated by name using theifr_name
field of theifreq
structure. Additionally, performs the actions ofBIOCFLUSH
. BIOCSRTIMEOUT
BIOCGRTIMEOUT
- (
struct timeval
) Set or get the read timeout parameter. The argument specifies the length of time to wait before timing out on a read request. This parameter is initialized to zero by open(2), indicating no timeout. BIOCGSTATS
- (
struct bpf_stat
) Returns the following structure of packet statistics:struct bpf_stat { u_int bs_recv; /* number of packets received */ u_int bs_drop; /* number of packets dropped */ };
The fields are:
bs_recv
- the number of packets received by the descriptor since opened or reset (including any buffered since the last read call); and
bs_drop
- the number of packets which were accepted by the filter but dropped by the kernel because of buffer overflows (i.e., the application's reads are not keeping up with the packet traffic).
BIOCIMMEDIATE
- (
u_int
) Enable or disable “immediate mode”, based on the truth value of the argument. When immediate mode is enabled, reads return immediately upon packet reception. Otherwise, a read will block until either the kernel buffer becomes full or a timeout occurs. This is useful for programs like rarpd(8) which must respond to messages in real time. The default for a new file is off. BIOCSETF
BIOCSETFNR
- (
struct bpf_program
) Sets the read filter program used by the kernel to discard uninteresting packets. An array of instructions and its length is passed in using the following structure:struct bpf_program { int bf_len; struct bpf_insn *bf_insns; };
The filter program is pointed to by the
bf_insns
field while its length in units of ‘struct bpf_insn
’ is given by thebf_len
field. See section FILTER MACHINE for an explanation of the filter language. The only difference betweenBIOCSETF
andBIOCSETFNR
isBIOCSETF
performs the actions ofBIOCFLUSH
whileBIOCSETFNR
does not. BIOCSETWF
- (
struct bpf_program
) Sets the write filter program used by the kernel to control what type of packets can be written to the interface. See theBIOCSETF
command for more information on thebpf
filter program. BIOCVERSION
- (
struct bpf_version
) Returns the major and minor version numbers of the filter language currently recognized by the kernel. Before installing a filter, applications must check that the current version is compatible with the running kernel. Version numbers are compatible if the major numbers match and the application minor is less than or equal to the kernel minor. The kernel version number is returned in the following structure:struct bpf_version { u_short bv_major; u_short bv_minor; };
The current version numbers are given by
BPF_MAJOR_VERSION
andBPF_MINOR_VERSION
from<net/bpf.h>
. An incompatible filter may result in undefined behavior (most likely, an error returned byioctl
() or haphazard packet matching). BIOCSHDRCMPLT
BIOCGHDRCMPLT
- (
u_int
) Set or get the status of the “header complete” flag. Set to zero if the link level source address should be filled in automatically by the interface output routine. Set to one if the link level source address will be written, as provided, to the wire. This flag is initialized to zero by default. BIOCSSEESENT
BIOCGSEESENT
- (
u_int
) These commands are obsolete but left for compatibility. UseBIOCSDIRECTION
andBIOCGDIRECTION
instead. Set or get the flag determining whether locally generated packets on the interface should be returned by BPF. Set to zero to see only incoming packets on the interface. Set to one to see packets originating locally and remotely on the interface. This flag is initialized to one by default. BIOCSDIRECTION
BIOCGDIRECTION
- (
u_int
) Set or get the setting determining whether incoming, outgoing, or all packets on the interface should be returned by BPF. Set toBPF_D_IN
to see only incoming packets on the interface. Set toBPF_D_INOUT
to see packets originating locally and remotely on the interface. Set toBPF_D_OUT
to see only outgoing packets on the interface. This setting is initialized toBPF_D_INOUT
by default. BIOCSTSTAMP
BIOCGTSTAMP
- (
u_int
) Set or get format and resolution of the time stamps returned by BPF. Set toBPF_T_MICROTIME
,BPF_T_MICROTIME_FAST
,BPF_T_MICROTIME_MONOTONIC
, orBPF_T_MICROTIME_MONOTONIC_FAST
to get time stamps in 64-bit struct timeval format. Set toBPF_T_NANOTIME
,BPF_T_NANOTIME_FAST
,BPF_T_NANOTIME_MONOTONIC
, orBPF_T_NANOTIME_MONOTONIC_FAST
to get time stamps in 64-bit struct timespec format. Set toBPF_T_BINTIME
,BPF_T_BINTIME_FAST
,BPF_T_NANOTIME_MONOTONIC
, orBPF_T_BINTIME_MONOTONIC_FAST
to get time stamps in 64-bit struct bintime format. Set toBPF_T_NONE
to ignore time stamp. All 64-bit time stamp formats are wrapped in struct bpf_ts. TheBPF_T_MICROTIME_FAST
,BPF_T_NANOTIME_FAST
,BPF_T_BINTIME_FAST
,BPF_T_MICROTIME_MONOTONIC_FAST
,BPF_T_NANOTIME_MONOTONIC_FAST
, andBPF_T_BINTIME_MONOTONIC_FAST
are analogs of corresponding formats without _FAST suffix but do not perform a full time counter query, so their accuracy is one timer tick. TheBPF_T_MICROTIME_MONOTONIC
,BPF_T_NANOTIME_MONOTONIC
,BPF_T_BINTIME_MONOTONIC
,BPF_T_MICROTIME_MONOTONIC_FAST
,BPF_T_NANOTIME_MONOTONIC_FAST
, andBPF_T_BINTIME_MONOTONIC_FAST
store the time elapsed since kernel boot. This setting is initialized toBPF_T_MICROTIME
by default. BIOCFEEDBACK
- (
u_int
) Set packet feedback mode. This allows injected packets to be fed back as input to the interface when output via the interface is successful. WhenBPF_D_INOUT
direction is set, injected outgoing packet is not returned by BPF to avoid duplication. This flag is initialized to zero by default. BIOCLOCK
- Set the locked flag on the
bpf
descriptor. This prevents the execution of ioctl commands which could change the underlying operating parameters of the device. BIOCGETBUFMODE
BIOCSETBUFMODE
- (
u_int
) Get or set the currentbpf
buffering mode; possible values areBPF_BUFMODE_BUFFER
, buffered read mode, andBPF_BUFMODE_ZBUF
, zero-copy buffer mode. BIOCSETZBUF
- (
struct bpf_zbuf
) Set the current zero-copy buffer locations; buffer locations may be set only once zero-copy buffer mode has been selected, and prior to attaching to an interface. Buffers must be of identical size, page-aligned, and an integer multiple of pages in size. The three fields bz_bufa, bz_bufb, and bz_buflen must be filled out. If buffers have already been set for this device, the ioctl will fail. BIOCGETZMAX
- (
size_t
) Get the largest individual zero-copy buffer size allowed. As two buffers are used in zero-copy buffer mode, the limit (in practice) is twice the returned size. As zero-copy buffers consume kernel address space, conservative selection of buffer size is suggested, especially when there are multiplebpf
descriptors in use on 32-bit systems. BIOCROTZBUF
- Force ownership of the next buffer to be assigned to userspace, if any data present in the buffer. If no data is present, the buffer will remain owned by the kernel. This allows consumers of zero-copy buffering to implement timeouts and retrieve partially filled buffers. In order to handle the case where no data is present in the buffer and therefore ownership is not assigned, the user process must check bzh_kernel_gen against bzh_user_gen.
BPF HEADER¶
One of the following structures is prepended to each packet returned by read(2) or via a zero-copy buffer:struct bpf_xhdr { struct bpf_ts bh_tstamp; /* time stamp */ uint32_t bh_caplen; /* length of captured portion */ uint32_t bh_datalen; /* original length of packet */ u_short bh_hdrlen; /* length of bpf header (this struct plus alignment padding) */ }; struct bpf_hdr { struct timeval bh_tstamp; /* time stamp */ uint32_t bh_caplen; /* length of captured portion */ uint32_t bh_datalen; /* original length of packet */ u_short bh_hdrlen; /* length of bpf header (this struct plus alignment padding) */ };
The fields, whose values are stored in host order, and are:
bh_tstamp
- The time at which the packet was processed by the packet filter.
bh_caplen
- The length of the captured portion of the packet. This is the minimum of the truncation amount specified by the filter and the length of the packet.
bh_datalen
- The length of the packet off the wire. This value is independent of the truncation amount specified by the filter.
bh_hdrlen
- The length of the
bpf
header, which may not be equal tosizeof
(struct bpf_xhdr) orsizeof
(struct bpf_hdr).
The bh_hdrlen
field exists to account for
padding between the header and the link level protocol. The purpose here is
to guarantee proper alignment of the packet data structures, which is
required on alignment sensitive architectures and improves performance on
many other architectures. The packet filter ensures that the
bpf_xhdr, bpf_hdr and the
network layer header will be word aligned. Currently,
bpf_hdr is used when the time stamp is set to
BPF_T_MICROTIME
,
BPF_T_MICROTIME_FAST
,
BPF_T_MICROTIME_MONOTONIC
,
BPF_T_MICROTIME_MONOTONIC_FAST
, or
BPF_T_NONE
for backward compatibility reasons.
Otherwise, bpf_xhdr is used. However,
bpf_hdr may be deprecated in the near future. Suitable
precautions must be taken when accessing the link layer protocol fields on
alignment restricted machines. (This is not a problem on an Ethernet, since
the type field is a short falling on an even offset, and the addresses are
probably accessed in a bytewise fashion).
Additionally, individual packets are padded so that each starts on
a word boundary. This requires that an application has some knowledge of how
to get from packet to packet. The macro
BPF_WORDALIGN
is defined in
<net/bpf.h>
to facilitate
this process. It rounds up its argument to the nearest word aligned value
(where a word is BPF_ALIGNMENT
bytes wide).
For example, if ‘p
’ points
to the start of a packet, this expression will advance it to the next
packet:
p = (char *)p +
BPF_WORDALIGN(p->bh_hdrlen + p->bh_caplen)
For the alignment mechanisms to work properly, the buffer passed to read(2) must itself be word aligned. The malloc(3) function will always return an aligned buffer.
FILTER MACHINE¶
A filter program is an array of instructions, with all branches forwardly directed, terminated by a return instruction. Each instruction performs some action on the pseudo-machine state, which consists of an accumulator, index register, scratch memory store, and implicit program counter.The following structure defines the instruction format:
struct bpf_insn { u_short code; u_char jt; u_char jf; u_long k; };
The k
field is used in different ways by
different instructions, and the jt
and
jf
fields are used as offsets by the branch
instructions. The opcodes are encoded in a semi-hierarchical fashion. There
are eight classes of instructions: BPF_LD
,
BPF_LDX
, BPF_ST
,
BPF_STX
, BPF_ALU
,
BPF_JMP
, BPF_RET
, and
BPF_MISC
. Various other mode and operator bits are
or'd into the class to give the actual instructions. The classes and modes
are defined in
<net/bpf.h>
.
Below are the semantics for each defined
bpf
instruction. We use the convention that A is the
accumulator, X is the index register, P[] packet data, and M[] scratch
memory store. P[i:n] gives the data at byte offset “i” in the
packet, interpreted as a word (n=4), unsigned halfword (n=2), or unsigned
byte (n=1). M[i] gives the i'th word in the scratch memory store, which is
only addressed in word units. The memory store is indexed from 0 to
BPF_MEMWORDS
- 1. k
,
jt
, and jf
are the
corresponding fields in the instruction definition. “len”
refers to the length of the packet.
BPF_LD
- These instructions copy a value into the accumulator. The type of the
source operand is specified by an “addressing mode” and can
be a constant (
BPF_IMM
), packet data at a fixed offset (BPF_ABS
), packet data at a variable offset (BPF_IND
), the packet length (BPF_LEN
), or a word in the scratch memory store (BPF_MEM
). ForBPF_IND
andBPF_ABS
, the data size must be specified as a word (BPF_W
), halfword (BPF_H
), or byte (BPF_B
). The semantics of all the recognizedBPF_LD
instructions follow.BPF_LD+BPF_W+BPF_ABS A <- P[k:4] BPF_LD+BPF_H+BPF_ABS A <- P[k:2] BPF_LD+BPF_B+BPF_ABS A <- P[k:1] BPF_LD+BPF_W+BPF_IND A <- P[X+k:4] BPF_LD+BPF_H+BPF_IND A <- P[X+k:2] BPF_LD+BPF_B+BPF_IND A <- P[X+k:1] BPF_LD+BPF_W+BPF_LEN A <- len BPF_LD+BPF_IMM A <- k BPF_LD+BPF_MEM A <- M[k]
BPF_LDX
- These instructions load a value into the index register. Note that the
addressing modes are more restrictive than those of the accumulator loads,
but they include
BPF_MSH
, a hack for efficiently loading the IP header length.BPF_LDX+BPF_W+BPF_IMM X <- k BPF_LDX+BPF_W+BPF_MEM X <- M[k] BPF_LDX+BPF_W+BPF_LEN X <- len BPF_LDX+BPF_B+BPF_MSH X <- 4*(P[k:1]&0xf)
BPF_ST
- This instruction stores the accumulator into the scratch memory. We do not
need an addressing mode since there is only one possibility for the
destination.
BPF_ST M[k] <- A
BPF_STX
- This instruction stores the index register in the scratch memory store.
BPF_STX M[k] <- X
BPF_ALU
- The alu instructions perform operations between the accumulator and index
register or constant, and store the result back in the accumulator. For
binary operations, a source mode is required
(
BPF_K
orBPF_X
).BPF_ALU+BPF_ADD+BPF_K A <- A + k BPF_ALU+BPF_SUB+BPF_K A <- A - k BPF_ALU+BPF_MUL+BPF_K A <- A * k BPF_ALU+BPF_DIV+BPF_K A <- A / k BPF_ALU+BPF_AND+BPF_K A <- A & k BPF_ALU+BPF_OR+BPF_K A <- A | k BPF_ALU+BPF_LSH+BPF_K A <- A << k BPF_ALU+BPF_RSH+BPF_K A <- A >> k BPF_ALU+BPF_ADD+BPF_X A <- A + X BPF_ALU+BPF_SUB+BPF_X A <- A - X BPF_ALU+BPF_MUL+BPF_X A <- A * X BPF_ALU+BPF_DIV+BPF_X A <- A / X BPF_ALU+BPF_AND+BPF_X A <- A & X BPF_ALU+BPF_OR+BPF_X A <- A | X BPF_ALU+BPF_LSH+BPF_X A <- A << X BPF_ALU+BPF_RSH+BPF_X A <- A >> X BPF_ALU+BPF_NEG A <- -A
BPF_JMP
- The jump instructions alter flow of control. Conditional jumps compare the
accumulator against a constant (
BPF_K
) or the index register (BPF_X
). If the result is true (or non-zero), the true branch is taken, otherwise the false branch is taken. Jump offsets are encoded in 8 bits so the longest jump is 256 instructions. However, the jump always (BPF_JA
) opcode uses the 32 bitk
field as the offset, allowing arbitrarily distant destinations. All conditionals use unsigned comparison conventions.BPF_JMP+BPF_JA pc += k BPF_JMP+BPF_JGT+BPF_K pc += (A > k) ? jt : jf BPF_JMP+BPF_JGE+BPF_K pc += (A >= k) ? jt : jf BPF_JMP+BPF_JEQ+BPF_K pc += (A == k) ? jt : jf BPF_JMP+BPF_JSET+BPF_K pc += (A & k) ? jt : jf BPF_JMP+BPF_JGT+BPF_X pc += (A > X) ? jt : jf BPF_JMP+BPF_JGE+BPF_X pc += (A >= X) ? jt : jf BPF_JMP+BPF_JEQ+BPF_X pc += (A == X) ? jt : jf BPF_JMP+BPF_JSET+BPF_X pc += (A & X) ? jt : jf
BPF_RET
- The return instructions terminate the filter program and specify the
amount of packet to accept (i.e., they return the truncation amount). A
return value of zero indicates that the packet should be ignored. The
return value is either a constant (
BPF_K
) or the accumulator (BPF_A
).BPF_RET+BPF_A accept A bytes BPF_RET+BPF_K accept k bytes
BPF_MISC
- The miscellaneous category was created for anything that does not fit into
the above classes, and for any new instructions that might need to be
added. Currently, these are the register transfer instructions that copy
the index register to the accumulator or vice versa.
BPF_MISC+BPF_TAX X <- A BPF_MISC+BPF_TXA A <- X
The bpf
interface provides the following
macros to facilitate array initializers:
BPF_STMT
(opcode,
operand) and
BPF_JUMP
(opcode,
operand, true_offset,
false_offset).
SYSCTL VARIABLES¶
A set of sysctl(8) variables controls the behaviour of thebpf
subsystem
- net.bpf.optimize_writers: 0
- Various programs use BPF to send (but not receive) raw packets (cdpd,
lldpd, dhcpd, dhcp relays, etc. are good examples of such programs). They
do not need incoming packets to be send to them. Turning this option on
makes new BPF users to be attached to write-only interface list until
program explicitly specifies read filter via
pcap_set_filter
(). This removes any performance degradation for high-speed interfaces. - net.bpf.stats:
- Binary interface for retrieving general statistics.
- net.bpf.zerocopy_enable: 0
- Permits zero-copy to be used with net BPF readers. Use with caution.
- net.bpf.maxinsns: 512
- Maximum number of instructions that BPF program can contain. Use
tcpdump(1)
-d
option to determine approximate number of instruction for any filter. - net.bpf.maxbufsize: 524288
- Maximum buffer size to allocate for packets buffer.
- net.bpf.bufsize: 4096
- Default buffer size to allocate for packets buffer.
EXAMPLES¶
The following filter is taken from the Reverse ARP Daemon. It accepts only Reverse ARP requests.struct bpf_insn insns[] = { BPF_STMT(BPF_LD+BPF_H+BPF_ABS, 12), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, ETHERTYPE_REVARP, 0, 3), BPF_STMT(BPF_LD+BPF_H+BPF_ABS, 20), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, REVARP_REQUEST, 0, 1), BPF_STMT(BPF_RET+BPF_K, sizeof(struct ether_arp) + sizeof(struct ether_header)), BPF_STMT(BPF_RET+BPF_K, 0), };
This filter accepts only IP packets between host 128.3.112.15 and 128.3.112.35.
struct bpf_insn insns[] = { BPF_STMT(BPF_LD+BPF_H+BPF_ABS, 12), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, ETHERTYPE_IP, 0, 8), BPF_STMT(BPF_LD+BPF_W+BPF_ABS, 26), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, 0x8003700f, 0, 2), BPF_STMT(BPF_LD+BPF_W+BPF_ABS, 30), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, 0x80037023, 3, 4), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, 0x80037023, 0, 3), BPF_STMT(BPF_LD+BPF_W+BPF_ABS, 30), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, 0x8003700f, 0, 1), BPF_STMT(BPF_RET+BPF_K, (u_int)-1), BPF_STMT(BPF_RET+BPF_K, 0), };
Finally, this filter returns only TCP finger packets. We must
parse the IP header to reach the TCP header. The
BPF_JSET
instruction checks that the IP fragment
offset is 0 so we are sure that we have a TCP header.
struct bpf_insn insns[] = { BPF_STMT(BPF_LD+BPF_H+BPF_ABS, 12), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, ETHERTYPE_IP, 0, 10), BPF_STMT(BPF_LD+BPF_B+BPF_ABS, 23), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, IPPROTO_TCP, 0, 8), BPF_STMT(BPF_LD+BPF_H+BPF_ABS, 20), BPF_JUMP(BPF_JMP+BPF_JSET+BPF_K, 0x1fff, 6, 0), BPF_STMT(BPF_LDX+BPF_B+BPF_MSH, 14), BPF_STMT(BPF_LD+BPF_H+BPF_IND, 14), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, 79, 2, 0), BPF_STMT(BPF_LD+BPF_H+BPF_IND, 16), BPF_JUMP(BPF_JMP+BPF_JEQ+BPF_K, 79, 0, 1), BPF_STMT(BPF_RET+BPF_K, (u_int)-1), BPF_STMT(BPF_RET+BPF_K, 0), };
SEE ALSO¶
tcpdump(1), ioctl(2), kqueue(2), poll(2), select(2), byteorder(3), ng_bpf(4), bpf(9)McCanne, S. and Jacobson V., An efficient, extensible, and portable network monitor.
HISTORY¶
The Enet packet filter was created in 1980 by Mike Accetta and Rick Rashid at Carnegie-Mellon University. Jeffrey Mogul, at Stanford, ported the code to BSD and continued its development from 1983 on. Since then, it has evolved into the Ultrix Packet Filter at DEC, a STREAMS NIT module under SunOS 4.1, and BPF.AUTHORS¶
Steven McCanne, of Lawrence Berkeley Laboratory, implemented BPF in Summer 1990. Much of the design is due to Van Jacobson.Support for zero-copy buffers was added by Robert N. M. Watson under contract to Seccuris Inc.
BUGS¶
The read buffer must be of a fixed size (returned by theBIOCGBLEN
ioctl).
A file that does not request promiscuous mode may receive promiscuously received packets as a side effect of another file requesting this mode on the same hardware interface. This could be fixed in the kernel with additional processing overhead. However, we favor the model where all files must assume that the interface is promiscuous, and if so desired, must utilize a filter to reject foreign packets.
Data link protocols with variable length headers are not currently supported.
The SEESENT
,
DIRECTION
, and FEEDBACK
settings have been observed to work incorrectly on some interface types,
including those with hardware loopback rather than software loopback, and
point-to-point interfaces. They appear to function correctly on a broad
range of Ethernet-style interfaces.
June 15, 2010 | Linux 4.9.0-9-amd64 |