fping - send ICMP ECHO_REQUEST packets to network hosts
] [ systems...
] [ systems...
is a program like ping
which uses the Internet Control
Message Protocol (ICMP) echo request to determine if a target host is
differs from ping
in that you can specify any
number of targets on the command line, or specify a file containing the lists
of targets to ping. Instead of sending to one target until it times out or
will send out a ping packet and move on to the next
target in a round-robin fashion. In the default mode, if a target replies, it
is noted and removed from the list of targets to check; if a target does not
respond within a certain time limit and/or retry limit it is designated as
also supports sending a specified number of pings to
a target, or looping indefinitely (as in ping
). Unlike ping
is meant to be used in scripts, so its output is designed to be
easy to parse.
The binary named fping6
is the same as fping
, except that it uses
IPv6 addresses instead of IPv4.
- Show systems that are alive.
- Display targets by address rather than DNS name.
- -b n
- Number of bytes of ping data to send. The minimum size (normally 12)
allows room for the data that fping needs to do its work (sequence
number, timestamp). The reported received data size includes the IP header
(normally 20 bytes) and ICMP header (8 bytes), so the minimum total size
is 40 bytes. Default is 56, as in ping. Maximum is the theoretical
maximum IP datagram size (64K), though most systems limit this to a
smaller, system-dependent number.
- -B n
- Backoff factor. In the default mode, fping sends several requests
to a target before giving up, waiting longer for a reply on each
successive request. This parameter is the value by which the wait time (
-t) is multiplied on each successive request; it must be entered as
a floating-point number (x.y). The default is 1.5.
- -c n
- Number of request packets to send to each target. In this mode, a line is
displayed for each received response (this can suppressed with -q
or -Q). Also, statistics about responses for each target are
displayed when all requests have been sent (or when interrupted).
- -C n
- Similar to -c, but the per-target statistics are displayed in a
format designed for automated response-time statistics gathering. For
% fping -C 5 -q somehost
somehost : 91.7 37.0 29.2 - 36.8
shows the response time in milliseconds for each of the five requests, with
the "-" indicating that no response was received to the fourth
- Use DNS to lookup address of return ping packet. This allows you to give
fping a list of IP addresses as input and print hostnames in the
- Add Unix timestamps in front of output lines generated with in looping or
counting modes ( -l, -c, or -C).
- Show elapsed (round-trip) time of packets.
- Read list of targets from a file. This option can only be used by the root
user. Regular users should pipe in the file via stdin:
% fping < targets_file
- -g addr/mask
- Generate a target list from a supplied IP netmask, or a starting and
ending IP. Specify the netmask or start/end in the targets portion of the
command line. If a network with netmask is given, the network and
broadcast addresses will be excluded. ex. To ping the network
192.168.1.0/24, the specified command line could look like either:
fping -g 192.168.1.0/24
fping -g 192.168.1.1 192.168.1.254
- Print usage message.
- -i n
- The minimum amount of time (in milliseconds) between sending a ping packet
to any target (default is 25).
- Loop sending packets to each target indefinitely. Can be interrupted with
Ctrl-C; statistics about responses for each target are then
- Send pings to each of a target host's multiple interfaces.
- Same as -d.
- -p <n>
- In looping or counting modes (-l, -c, or -C), this
parameter sets the time in milliseconds that fping waits between
successive packets to an individual target. Default is 1000.
- Quiet. Don't show per-probe results, but only the final summary. Also
don't show ICMP error messages.
- -Q n
- Like -q, but show summary results every n seconds.
- -r n
- Retry limit (default 3). This is the number of times an attempt at pinging
a target will be made, not including the first try.
- Print cumulative statistics upon exit.
- -S addr
- Set source address.
- -I if
- Set the interface (requires SO_BINDTODEVICE support)
- -t n
- Initial target timeout in milliseconds (default 500). In the default mode,
this is the amount of time that fping waits for a response to its
first request. Successive timeouts are multiplied by the backoff factor
specified with -B. Note that this option has no effect looping or
counting modes ( -l, -c, or -C).
- -T n
- Ignored (for compatibility with fping 2.4).
- Show targets that are unreachable.
- -O n
- Set the typ of service flag (TOS). n can be either decimal or
hexadecimal (0xh) format.
- Print fping version information.
- -H n
- Set the IP TTL field (time to live hops).
- Roland J. Schemers III, Stanford University, concept and versions 1.x
- RL "Bob" Morgan, Stanford University, versions 2.x
- David Papp, versions 2.3x and up
fping website: <http://www.fping.org>
- David Schweikert, versions 3.0 and up
Exit status is 0 if all the hosts are reachable, 1 if some hosts were
unreachable, 2 if any IP addresses were not found, 3 for invalid command line
arguments, and 4 for a system call failure.
If certain options are used (i.e, a low value for -i
, and a
high value for -r
) it is possible to flood the network. This program
must be installed as setuid root in order to open up a raw socket, or must be
run by root. In order to stop mere mortals from hosing the network, normal
users can't specify the following:
- -i n, where n < 10 msec
- -r n, where n > 20
- -t n, where n < 250 msec