ANYTUN-CONFIG(8) | ANYTUN-CONFIG(8) |
NAME¶
anytun-config - anycast tunneling configuration utilitySYNOPSIS¶
anytun-config [ -h|--help ] [ -L|--log <target>:<level>[,<param1>[,<param2>[..]]] [ -U|--debug ] [ -r|--remote-host <hostname|ip> ] [ -o|--remote-port <port> ] [ -4|--ipv4-only ] [ -6|--ipv6-only ] [ -R|--route <net>/<prefix length> ] [ -m|--mux <mux-id> ] [ -w|--window-size <window size> ] [ -k|--kd-prf <kd-prf type> ] [ -e|--role <role> ] [ -E|--passphrase <pass phrase> ] [ -K|--key <master key> ] [ -A|--salt <master salt> ]
DESCRIPTION¶
anytun-config writes routing/connection table entries, that can be read by anytun-controld.OPTIONS¶
-L, --log <target>:<level>[,<param1>[,<param2>[..]]]add log target to logging system. This can be invoked
several times in order to log to different targets at the same time. Every
target hast its own log level which is a number between 0 and 5. Where 0 means
disabling log and 5 means debug messages are enabled.
The file target can be used more the once with different levels. If no target is
provided at the command line a single target with the config
syslog:3,anytun-config,daemon is added.
The following targets are supported:
syslog
-U, --debug
log to syslog daemon, parameters
<level>[,<logname>[,<facility>]]
file
log to file, parameters
<level>[,<path>]
stdout
log to standard output, parameters <level>
stderr
log to standard error, parameters <level>
This option instructs Anytun to run in debug mode.
It implicits -D (don’t daemonize) and adds a log target with the
configuration stdout:5 (logging with maximum level). In future releases
there might be additional output when this option is supplied.
-r, --remote-host <hostname|ip>
This option can be used to specify the remote tunnel
endpoint. In case of anycast tunnel endpoints, the anycast IP address has to
be used. If you do not specify an address, it is automatically determined
after receiving the first data packet.
-o, --remote-port <port>
The UDP port used for payload data by the remote host
(specified with -p on the remote host). If you do not specify a port, it is
automatically determined after receiving the first data packet.
-4, --ipv4-only
Resolv to IPv4 addresses only. The default is to resolv
both IPv4 and IPv6 addresses.
-6, --ipv6-only
Resolv to IPv6 addresses only. The default is to resolv
both IPv4 and IPv6 addresses.
-R, --route <net>/<prefix length>
add a route to connection. This can be invoked several
times.
-m, --mux <mux-id>
the multiplex id to use. default: 0
-w, --window-size <window size>
seqence window size
Sometimes, packets arrive out of order on the receiver side. This option defines
the size of a list of received packets' sequence numbers. If, according to
this list, a received packet has been previously received or has been
transmitted in the past, and is therefore not in the list anymore, this is
interpreted as a replay attack and the packet is dropped. A value of 0
deactivates this list and, as a consequence, the replay protection employed by
filtering packets according to their secuence number. By default the sequence
window is disabled and therefore a window size of 0 is used.
-k, --kd—prf <kd-prf type>
key derivation pseudo random function
The pseudo random function which is used for calculating the session keys and
session salt.
Possible values:
null
-e, --role <role>
no random function, keys and salt are set to 0..00
aes-ctr
AES in counter mode with 128 Bits, default value
aes-ctr-128
AES in counter mode with 128 Bits
aes-ctr-192
AES in counter mode with 192 Bits
aes-ctr-256
AES in counter mode with 256 Bits
SATP uses different session keys for inbound and outbound
traffic. The role parameter is used to determine which keys to use for
outbound or inbound packets. On both sides of a vpn connection different roles
have to be used. Possible values are left and right. You may
also use alice or server as a replacement for left and
bob or client as a replacement for right. By default
left is used.
-E, --passphrase <pass phrase>
This passphrase is used to generate the master key and
master salt. For the master key the last n bits of the SHA256 digest of the
passphrase (where n is the length of the master key in bits) is used. The
master salt gets generated with the SHA1 digest. You may force a specific key
and or salt by using --key and --salt.
-K, --key <master key>
master key to use for key derivation
Master key in hexadecimal notation, e.g. 01a2b3c4d5e6f708a9b0cadbecfd0fa1, with
a mandatory length of 32, 48 or 64 characters (128, 192 or 256 bits).
-A, --salt <master salt>
master salt to use for key derivation
Master salt in hexadecimal notation, e.g. 01a2b3c4d5e6f708a9b0cadbecfd, with a
mandatory length of 28 characters (14 bytes).
EXAMPLES¶
Add a client with Connection ID (Mux) 12 and add 2 Routes to this client# anytun-config -w 0 -m 12 -K 0123456789ABCDEFFEDCBA9876543210 -A 0123456789ABCDDCBA9876543210 \ -R 192.0.2.0/24 -R 192.168.1.1/32 -e server >> routingtable
BUGS¶
Most likely there are some bugs in Anytun. If you find a bug, please let the developers know at satp@anytun.org. Of course, patches are preferred.SEE ALSO¶
anytun(8), anytun-controld(8), anytun-showtables(8)AUTHORS¶
Othmar Gsenger <otti@anytun.org> Erwin Nindl <nine@anytun.org> Christian Pointner <equinox@anytun.org>RESOURCES¶
Main web site: http://www.anytun.org/COPYING¶
Copyright (C) 2007-2014 Markus Grüneis, Othmar Gsenger, Erwin Nindl and Christian Pointner. This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or any later version.08/26/2014 |