other versions
ENUM MAC80211_RX_FLA(9) | The basic mac80211 driver inte | ENUM MAC80211_RX_FLA(9) |
NAME¶
enum_mac80211_rx_flags - receive flagsSYNOPSIS¶
enum mac80211_rx_flags { RX_FLAG_MMIC_ERROR, RX_FLAG_DECRYPTED, RX_FLAG_MACTIME_PLCP_START, RX_FLAG_MMIC_STRIPPED, RX_FLAG_IV_STRIPPED, RX_FLAG_FAILED_FCS_CRC, RX_FLAG_FAILED_PLCP_CRC, RX_FLAG_MACTIME_START, RX_FLAG_SHORTPRE, RX_FLAG_HT, RX_FLAG_40MHZ, RX_FLAG_SHORT_GI, RX_FLAG_NO_SIGNAL_VAL, RX_FLAG_HT_GF, RX_FLAG_AMPDU_DETAILS, RX_FLAG_PN_VALIDATED, RX_FLAG_DUP_VALIDATED, RX_FLAG_AMPDU_LAST_KNOWN, RX_FLAG_AMPDU_IS_LAST, RX_FLAG_AMPDU_DELIM_CRC_ERROR, RX_FLAG_AMPDU_DELIM_CRC_KNOWN, RX_FLAG_MACTIME_END, RX_FLAG_VHT, RX_FLAG_LDPC, RX_FLAG_ONLY_MONITOR, RX_FLAG_SKIP_MONITOR, RX_FLAG_STBC_MASK, RX_FLAG_10MHZ, RX_FLAG_5MHZ, RX_FLAG_AMSDU_MORE, RX_FLAG_RADIOTAP_VENDOR_DATA, RX_FLAG_MIC_STRIPPED, RX_FLAG_ALLOW_SAME_PN };
CONSTANTS¶
RX_FLAG_MMIC_ERRORMichael MIC error was reported on this frame. Use
together with RX_FLAG_MMIC_STRIPPED.
RX_FLAG_DECRYPTED
This frame was decrypted in hardware.
RX_FLAG_MACTIME_PLCP_START
The timestamp passed in the RX status (mactime
field) is valid and contains the time the SYNC preamble was received.
RX_FLAG_MMIC_STRIPPED
the Michael MIC is stripped off this frame, verification
has been done by the hardware.
RX_FLAG_IV_STRIPPED
The IV/ICV are stripped from this frame. If this flag is
set, the stack cannot do any replay detection hence the driver or hardware
will have to do that.
RX_FLAG_FAILED_FCS_CRC
Set this flag if the FCS check failed on the frame.
RX_FLAG_FAILED_PLCP_CRC
Set this flag if the PCLP check failed on the
frame.
RX_FLAG_MACTIME_START
The timestamp passed in the RX status (mactime
field) is valid and contains the time the first symbol of the MPDU was
received. This is useful in monitor mode and for proper IBSS merging.
RX_FLAG_SHORTPRE
Short preamble was used for this frame
RX_FLAG_HT
HT MCS was used and rate_idx is MCS index
RX_FLAG_40MHZ
HT40 (40 MHz) was used
RX_FLAG_SHORT_GI
Short guard interval was used
RX_FLAG_NO_SIGNAL_VAL
The signal strength value is not present. Valid only for
data frames (mainly A-MPDU)
RX_FLAG_HT_GF
This frame was received in a HT-greenfield transmission,
if the driver fills this value it should add
IEEE80211_RADIOTAP_MCS_HAVE_FMT to hw.radiotap_mcs_details to advertise
that fact
RX_FLAG_AMPDU_DETAILS
A-MPDU details are known, in particular the reference
number ( ampdu_reference) must be populated and be a distinct number
for each A-MPDU
RX_FLAG_PN_VALIDATED
Currently only valid for CCMP/GCMP frames, this flag
indicates that the PN was verified for replay protection. Note that this flag
is also currently only supported when a frame is also decrypted (ie.
RX_FLAG_DECRYPTED must be set)
RX_FLAG_DUP_VALIDATED
The driver should set this flag if it did de-duplication
by itself.
RX_FLAG_AMPDU_LAST_KNOWN
last subframe is known, should be set on all subframes of
a single A-MPDU
RX_FLAG_AMPDU_IS_LAST
this subframe is the last subframe of the A-MPDU
RX_FLAG_AMPDU_DELIM_CRC_ERROR
A delimiter CRC error has been detected on this
subframe
RX_FLAG_AMPDU_DELIM_CRC_KNOWN
The delimiter CRC field is known (the CRC is stored in
the ampdu_delimiter_crc field)
RX_FLAG_MACTIME_END
The timestamp passed in the RX status (mactime
field) is valid and contains the time the last symbol of the MPDU (including
FCS) was received.
RX_FLAG_VHT
VHT MCS was used and rate_index is MCS index
RX_FLAG_LDPC
LDPC was used
RX_FLAG_ONLY_MONITOR
Report frame only to monitor interfaces without
processing it in any regular way. This is useful if drivers offload some
frames but still want to report them for sniffing purposes.
RX_FLAG_SKIP_MONITOR
Process and report frame to all interfaces except monitor
interfaces. This is useful if drivers offload some frames but still want to
report them for sniffing purposes.
RX_FLAG_STBC_MASK
STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
RX_FLAG_10MHZ
10 MHz (half channel) was used
RX_FLAG_5MHZ
5 MHz (quarter channel) was used
RX_FLAG_AMSDU_MORE
Some drivers may prefer to report separate A-MSDU
subframes instead of a one huge frame for performance reasons. All, but the
last MSDU from an A-MSDU should have this flag set. E.g. if an A-MSDU has 3
frames, the first 2 must have the flag set, while the 3rd (last) one must not
have this flag set. The flag is used to deal with retransmission/duplication
recovery properly since A-MSDU subframes share the same sequence number.
Reported subframes can be either regular MSDU or singly A-MSDUs. Subframes
must not be interleaved with other frames.
RX_FLAG_RADIOTAP_VENDOR_DATA
This frame contains vendor-specific radiotap data in the
skb->data (before the frame) as described by the struct
ieee80211_vendor_radiotap.
RX_FLAG_MIC_STRIPPED
The mic was stripped of this packet. Decryption was done
by the hardware
RX_FLAG_ALLOW_SAME_PN
Allow the same PN as same packet before. This is used for
AMSDU subframes which can have the same PN as the first subframe.
DESCRIPTION¶
These flags are used with the flag member of struct ieee80211_rx_status.AUTHOR¶
Johannes Berg <johannes@sipsolutions.net>Author.
COPYRIGHT¶
January 2017 | Kernel Hackers Manual 4.8. |