journald.conf, journald.conf.d, journald@.conf - Journal service configuration files
These files configure various parameters of the systemd journal service, systemd-journald.service(8). See systemd.syntax(7) for a general description of the syntax.
The systemd-journald instance managing the default namespace is configured by /etc/systemd/journald.conf and associated drop-ins. Instances managing other namespaces read /etc/systemd/journald@NAMESPACE.conf and associated drop-ins with the namespace identifier filled in. This allows each namespace to carry a distinct configuration. See systemd-journald.service(8) for details about journal namespaces.
CONFIGURATION DIRECTORIES AND PRECEDENCE¶
The default configuration is set during compilation, so configuration is only needed when it is necessary to deviate from those defaults. Initially, the main configuration file in /etc/systemd/ contains commented out entries showing the defaults as a guide to the administrator. Local overrides can be created by editing this file or by creating drop-ins, as described below. Using drop-ins for local configuration is recommended over modifications to the main configuration file.
In addition to the "main" configuration file, drop-in configuration snippets are read from /usr/lib/systemd/*.conf.d/, /usr/local/lib/systemd/*.conf.d/, and /etc/systemd/*.conf.d/. Those drop-ins have higher precedence and override the main configuration file. Files in the *.conf.d/ configuration subdirectories are sorted by their filename in lexicographic order, regardless of in which of the subdirectories they reside. When multiple files specify the same option, for options which accept just a single value, the entry in the file sorted last takes precedence, and for options which accept a list of values, entries are collected as they occur in the sorted files.
When packages need to customize the configuration, they can install drop-ins under /usr/. Files in /etc/ are reserved for the local administrator, who may use this logic to override the configuration files installed by vendor packages. Drop-ins have to be used to override package drop-ins, since the main configuration file has lower precedence. It is recommended to prefix all filenames in those subdirectories with a two-digit number and a dash, to simplify the ordering of the files.
To disable a configuration file supplied by the vendor, the recommended way is to place a symlink to /dev/null in the configuration directory in /etc/, with the same filename as the vendor configuration file.
All options are configured in the [Journal] section:
Note that journald will initially use volatile storage, until a call to journalctl --flush (or sending SIGUSR1 to journald) will cause it to switch to persistent logging (under the conditions mentioned above). This is done automatically on boot via "systemd-journal-flush.service".
Note that when this option is changed to "volatile", existing persistent data is not removed. In the other direction, journalctl(1) with the --flush option may be used to move volatile data to persistent storage.
Note that the effective rate limit is multiplied by a factor derived from the available free disk space for the journal. Currently, this factor is calculated using the base 2 logarithm.
Table 1. Example RateLimitBurst= rate modifications by the available disk space
|Available Disk Space||Burst Multiplier|
If a service provides rate limits for itself through
LogRateLimitIntervalSec= and/or LogRateLimitBurst= in systemd.exec(5), those values will override the settings specified here.
SystemMaxUse=, SystemKeepFree=, SystemMaxFileSize=, SystemMaxFiles=, RuntimeMaxUse=, RuntimeKeepFree=, RuntimeMaxFileSize=, RuntimeMaxFiles=
SystemMaxUse= and RuntimeMaxUse= control how much disk space the journal may use up at most. SystemKeepFree= and RuntimeKeepFree= control how much disk space systemd-journald shall leave free for other uses. systemd-journald will respect both limits and use the smaller of the two values.
The first pair defaults to 10% and the second to 15% of the size of the respective file system, but each value is capped to 4G. If the file system is nearly full and either SystemKeepFree= or RuntimeKeepFree= are violated when systemd-journald is started, the limit will be raised to the percentage that is actually free. This means that if there was enough free space before and journal files were created, and subsequently something else causes the file system to fill up, journald will stop using more space, but it will not be removing existing files to reduce the footprint again, either. Also note that only archived files are deleted to reduce the space occupied by journal files. This means that, in effect, there might still be more space used than SystemMaxUse= or RuntimeMaxUse= limit after a vacuuming operation is complete.
SystemMaxFileSize= and RuntimeMaxFileSize= control how large individual journal files may grow at most. This influences the granularity in which disk space is made available through rotation, i.e. deletion of historic data. Defaults to one eighth of the values configured with SystemMaxUse= and RuntimeMaxUse=, so that usually seven rotated journal files are kept as history.
Specify values in bytes or use K, M, G, T, P, E as units for the specified sizes (equal to 1024, 1024², ... bytes). Note that size limits are enforced synchronously when journal files are extended, and no explicit rotation step triggered by time is needed.
SystemMaxFiles= and RuntimeMaxFiles= control how many individual journal files to keep at most. Note that only archived files are deleted to reduce the number of files until this limit is reached; active files will stay around. This means that, in effect, there might still be more journal files around in total than this limit after a vacuuming operation is complete. This setting defaults to 100.
ForwardToSyslog=, ForwardToKMsg=, ForwardToConsole=, ForwardToWall=
When forwarding to the console, the TTY to log to can be changed with TTYPath=, described below.
When forwarding to the kernel log buffer (kmsg), make sure to select a suitably large size for the log buffer, for example by adding "log_buf_len=8M" to the kernel command line. systemd will automatically disable kernel's rate-limiting applied to userspace processes (equivalent to setting "printk.devkmsg=on").
MaxLevelStore=, MaxLevelSyslog=, MaxLevelKMsg=, MaxLevelConsole=, MaxLevelWall=
FORWARDING TO TRADITIONAL SYSLOG DAEMONS¶
Journal events can be transferred to a different logging daemon in two different ways. With the first method, messages are immediately forwarded to a socket (/run/systemd/journal/syslog), where the traditional syslog daemon can read them. This method is controlled by the ForwardToSyslog= option. With a second method, a syslog daemon behaves like a normal journal client, and reads messages from the journal files, similarly to journalctl(1). With this, messages do not have to be read immediately, which allows a logging daemon which is only started late in boot to access all messages since the start of the system. In addition, full structured meta-data is available to it. This method of course is available only if the messages are stored in a journal file at all. So it will not work if Storage=none is set. It should be noted that usually the second method is used by syslog daemons, so the Storage= option, and not the ForwardToSyslog= option, is relevant for them.
systemd(1), systemd-journald.service(8), journalctl(1), systemd.journal-fields(7), systemd-system.conf(5)
- Seekable Sequential Key Generators
- Users, Groups, UIDs and GIDs on systemd systems