Scroll to navigation

Config::Model::models::LCDd::picolcd(3pm) User Contributed Perl Documentation Config::Model::models::LCDd::picolcd(3pm)

NAME

Config::Model::models::LCDd::picolcd - Configuration class LCDd::picolcd

DESCRIPTION

Configuration classes used by Config::Model

generated from LCDd.conf

Elements

Backlight

Sets the initial state of the backlight upon start-up. Optional. Type boolean.
upstream_default value :
on

Brightness

Set the initial brightness . Works only with the 20x4 device. Optional. Type integer.
upstream_default value :
1000

Contrast

Set the initial contrast Optional. Type integer.
upstream_default value :
1000

Key0Light

If Keylights is on, the you can unlight specific keys below: Key0 is the directional pad. Key1 - Key5 correspond to the F1 - F5 keys. There is no LED for the +/- keys. This is a handy way to indicate to users which keys are disabled. Optional. Type boolean.
upstream_default value :
on

Key1Light

Optional. Type uniline.
default value :
on

Key2Light

Optional. Type uniline.
default value :
on

Key3Light

Optional. Type uniline.
default value :
on

Key4Light

Optional. Type uniline.
default value :
on

Key5Light

Optional. Type uniline.
default value :
on

KeyRepeatDelay

Key auto repeat is only available if the picoLCD driver is built with libusb-1.0. Use KeyRepeatDelay and KeyRepeatInterval to configure key auto repeat.

Key auto repeat delay (time in ms from first key report to first repeat). Use zero to disable auto repeat. Optional. Type integer.

upstream_default value :
300

KeyRepeatInterval

Key auto repeat interval (time in ms between repeat reports). Only used if KeyRepeatDelay is not zero. Optional. Type integer.
upstream_default value :
200

KeyTimeout

KeyTimeout is only used if the picoLCD driver is built with libusb-0.1. When built with libusb-1.0 key and IR data is input asynchronously so there is no need to wait for the USB data. KeyTimeout is the time in ms that LCDd spends waiting for a key press before cycling through other duties. Higher values make LCDd use less CPU time and make key presses more detectable. Lower values make LCDd more responsive but a little prone to missing key presses. 500 (.5 second) is the default and a balanced value. Optional. Type integer.
upstream_default value :
500

Keylights

Light the keys? Optional. Type boolean.
upstream_default value :
on

LinkLights

Link the key lights to the backlight? Optional. Type boolean.
upstream_default value :
on

LircFlushThreshold

Threshold in microseconds of the gap that triggers flushing the IR data to lirc If LircTime_us is on values greater than 32.767ms will disable the flush If LircTime_us is off values greater than 1.999938s will disable the flush. Optional. Type integer.
upstream_default value :
8000

LircHost

Host name or IP address of the LIRC instance that is to receive IR codes If not set, or set to an empty value, IR support is disabled. Optional. Type uniline.
upstream_default value :
127.0.0.1

LircPort

UDP port on which LIRC is listening Optional. Type integer.
upstream_default value :
8765

LircTime_us

UDP data time unit for LIRC On: times sent in microseconds (requires LIRC UDP driver that accepts this). Off: times sent in 'jiffies' (1/16384s) (supported by standard LIRC UDP driver). Optional. Type boolean.
upstream_default value :
off

OffBrightness

Set the brightness while the backlight is 'off' . Works only with the 20x4 device. Optional. Type integer.
upstream_default value :
0

SEE ALSO

cme
2017-12-13 perl v5.26.1