|IF_BRIDGE(4)||Device Drivers Manual||IF_BRIDGE(4)|
SYNOPSIS¶To compile this driver into the kernel, place the following line in your kernel configuration file:
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
if_bridgedriver creates a logical link between two or more IEEE 802 networks that use the same (or “similar enough”) framing format. For example, it is possible to bridge Ethernet and 802.11 networks together, but it is not possible to bridge Ethernet and Token Ring together.
if_bridge interface randomly chooses a
link (MAC) address in the range reserved for locally administered addresses
when it is created. This address is guaranteed to be unique
only across all
interfaces on the local machine. Thus you can theoretically have two bridges
on the different machines with the same link addresses. The address can be
changed by assigning the desired link address using
If sysctl(8) node net.link.bridge.inherit_mac has non-zero value, newly created bridge will inherit MAC address from its first member instead of choosing random link-level address. This will provide more predictable bridge MAC without any additional configuration, but currently this feature is known to break some L2 protocols, for example PPPoE that is provided by ng_pppoe(4) and ppp(8). Now this feature is considered as experimental and is turned off by-default.
A bridge can be used to provide several services, such as a simple 802.11-to-Ethernet bridge for wireless hosts, and traffic isolation.
A bridge works like a switch, forwarding traffic from one interface to another. Multicast and broadcast packets are always forwarded to all interfaces that are part of the bridge. For unicast traffic, the bridge learns which MAC addresses are associated with which interfaces and will forward the traffic selectively.
The MTU of the first member interface to be added is used as the bridge MTU. All additional members are required to have exactly the same value.
The TOE, TSO, TXCSUM and TXCSUM6 capabilities on all interfaces added to the bridge are disabled if any of the interfaces doesn't support/enable them. The LRO capability is always disabled. All the capabilities are restored when the interface is removed from bridge. Changing capabilities in run time may cause NIC reinit and the link flap.
The bridge supports “monitor mode”, where the packets are discarded after bpf(4) processing, and are not processed or forwarded further. This can be used to multiplex the input of two or more interfaces into a single bpf(4) stream. This is useful for reconstructing the traffic for network taps that transmit the RX/TX signals out through two separate interfaces.
AF_INET6address family on bridge interfaces. The following rc.conf(5) variable configures an IPv6 link-local address on
or in a more explicit manner:
AF_INET6 address family has a
concept of scope zone. Bridging multiple interfaces change the zone
configuration because multiple links are merged to each other and form a new
single link while the member interfaces still work individually. This means
each member interface still has a separate link-local scope zone and the
if_bridge interface has another single, aggregated
link-local scope zone at the same time. This situation is clearly against
the description “zones of the same scope cannot overlap” in
Section 5, RFC 4007. Although it works in most cases, it can cause some
conterintuitive or undesirable behavior in some edge cases when both of the
if_bridge interface and one of the member interface
have an IPv6 address and applications use both of them.
To prevent this situation,
checks whether a link-local scoped IPv6 address is configured on a member
interface to be added and the
if_bridge interface has IPv6 addresses,
IPv6 addresses on the member interface will be automatically removed before
the interface is added.
This behavior can be disabled by setting
AUTO_LINKLOCAL interface flag are not enabled by
if_bridge interface even when
net.inet6.ip6.auto_linklocal is set to
if_bridgedriver implements the Rapid Spanning Tree Protocol (RSTP or 802.1w) with backwards compatibility with the legacy Spanning Tree Protocol (STP). Spanning Tree is used to detect and remove loops in a network topology.
RSTP provides faster spanning tree convergence than legacy STP, the protocol will exchange information with neighbouring switches to quickly transition to forwarding without creating loops.
The code will default to RSTP mode but will downgrade any port connected to a legacy STP network so is fully backward compatible. A bridge can be forced to operate in STP mode without rapid state transitions via the proto command in ifconfig(8).
PACKET FILTERING¶Packet filtering can be used with any firewall package that hooks in via the pfil(9) framework. When filtering is enabled, bridged packets will pass through the filter inbound on the originating interface, on the bridge interface and outbound on the appropriate interfaces. Either stage can be disabled. The filtering behaviour can be controlled using sysctl(8):
- Controls the handling of non-IP packets which are not passed to
pfil(9). Set to
1to only allow IP packets to pass (subject to firewall rules), set to
0to unconditionally pass all non-IP Ethernet frames.
- Set to
1to enable filtering on the incoming and outgoing member interfaces, set to
0to disable it.
- Set to
1to enable filtering on the bridge interface, set to
0to disable it.
- Set to
1to additionally filter on the physical interface for locally destined packets. Set to
0to disable this feature.
- Set to
1to enable layer2 filtering with ipfirewall(4), set to
0to disable it. This needs to be enabled for dummynet(4) support. When ipfw is enabled, pfil_bridge and pfil_member will be disabled so that IPFW is not run twice; these can be re-enabled if desired.
- Set to
1to enable layer2 ARP filtering with ipfirewall(4), set to
0to disable it. Requires ipfw to be enabled.
ARP and REVARP packets are forwarded without being filtered and
others that are not IP nor IPv6 packets are not forwarded when
pfil_onlyip is enabled. IPFW can filter Ethernet types
mac-type so all packets are passed to the
filter for processing.
The packets originating from the bridging host will be seen by the filter on the interface that is looked up in the routing table.
The packets destined to the bridging host will be seen by the
filter on the interface with the MAC address equal to the packet's
destination MAC. There are situations when some of the bridge members are
sharing the same MAC address (for example the vlan(4)
interfaces: they are currently sharing the MAC address of the parent
physical interface). It is not possible to distinguish between these
interfaces using their MAC address, excluding the case when the packet's
destination MAC address is equal to the MAC address of the interface on
which the packet was entered to the system. In this case the filter will see
the incoming packet on this interface. In all other cases the interface seen
by the packet filter is chosen from the list of bridge members with the same
MAC address and the result strongly depends on the member addition sequence
and the actual implementation of
if_bridge. It is
not recommended to rely on the order chosen by the current
if_bridge implementation: it can be changed in the
The previous paragraph is best illustrated with the following pictures. Let
- the MAC address of the incoming packet's destination is
- the interface on which packet entered the system is
ifXMAC address is
- there are possibly other bridge members with the same MAC address
- the bridge has more than one interface that are sharing the same MAC
yy:yy:yy:yy:yy:yy; we will call them
Then if the MAC address
is equal to the
xx:xx:xx:xx:xx:xx then the filter
will see the packet on the interface
ifX no matter
if there are any other bridge members carrying the same MAC address. But if
the MAC address
nn:nn:nn:nn:nn:nn is equal to the
yy:yy:yy:yy:yy:yy then the interface that will be
seen by the filter is one of the
vlanYn. It is not
possible to predict the name of the actual interface without the knowledge
of the system state and the
This problem arises for any bridge members that are sharing the
same MAC address, not only to the vlan(4) ones: they we
taken just as the example of such situation. So if one wants the filter the
locally destined packets based on their interface name, one should be aware
of this implication. The described situation will appear at least on the
filtering bridges that are doing IP-forwarding; in some of such cases it is
better to assign the IP address only to the
if_bridge interface and not to the bridge members.
Enabling net.link.bridge.pfil_local_phys will let you
do the additional filtering on the physical interface.
EXAMPLES¶The following when placed in the file /etc/rc.conf will cause a bridge called “
bridge0” to be created, and will add the interfaces “
wlan0” and “
fxp0” to the bridge, and then enable packet forwarding. Such a configuration could be used to implement a simple 802.11-to-Ethernet bridge (assuming the 802.11 interface is in ad-hoc mode).
cloned_interfaces="bridge0" ifconfig_bridge0="addm wlan0 addm fxp0 up"
For the bridge to forward packets, all member interfaces and the bridge need to be up. The above example would also require:
create_args_wlan0="wlanmode hostap" ifconfig_wlan0="up ssid my_ap mode 11g" ifconfig_fxp0="up"
Consider a system with two 4-port Ethernet boards. The following will cause a bridge consisting of all 8 ports with Rapid Spanning Tree enabled to be created:
ifconfig bridge0 create ifconfig bridge0 \ addm fxp0 stp fxp0 \ addm fxp1 stp fxp1 \ addm fxp2 stp fxp2 \ addm fxp3 stp fxp3 \ addm fxp4 stp fxp4 \ addm fxp5 stp fxp5 \ addm fxp6 stp fxp6 \ addm fxp7 stp fxp7 \ up
The bridge can be used as a regular host interface at the same time as bridging between its member ports. In this example, the bridge connects em0 and em1, and will receive its IP address through DHCP:
cloned_interfaces="bridge0" ifconfig_bridge0="addm em0 addm em1 DHCP" ifconfig_em0="up" ifconfig_em1="up"
The bridge can tunnel Ethernet across an IP internet using the EtherIP protocol. This can be combined with ipsec(4) to provide an encrypted connection. Create a gif(4) interface and set the local and remote IP addresses for the tunnel, these are reversed on the remote bridge.
ifconfig gif0 create ifconfig gif0 tunnel 220.127.116.11 18.104.22.168 up ifconfig bridge0 create ifconfig bridge0 addm fxp0 addm gif0 up
Note that FreeBSD 6.1, 6.2, 6.3, 7.0, 7.1, and 7.2 have a bug in the EtherIP protocol. For more details and workaround, see gif(4) manual page.
SEE ALSO¶gif(4), ipf(4), ipfw(4), pf(4), ifconfig(8)
if_bridgedriver first appeared in FreeBSD 6.0.
bridgedriver was originally written by Jason L. Wright <firstname.lastname@example.org> as part of an undergraduate independent study at the University of North Carolina at Greensboro.
This version of the
if_bridge driver has
been heavily modified from the original version by Jason R.
Rapid Spanning Tree Protocol (RSTP) support was added by Andrew Thompson <thompsa@FreeBSD.org>.
if_bridgedriver currently supports only Ethernet and Ethernet-like (e.g., 802.11) network devices, with exactly the same interface MTU size as the bridge device.
|October 16, 2017||Linux 4.19.0-10-amd64|