Scroll to navigation

CH_WAVE(1) General Commands Manual CH_WAVE(1)

NAME

ch_wavechange/copy/combine waveform files

SYNOPSIS

ch_wave [-h] [-itype file type] [-n channels] [-f sample rate] [-ibo byte order] [-iswap] [-istype sample type] [-c channel] [-start seconds] [-end seconds] [-from sample] [-to sample] [-o output file] [-otype file type] [-F sample rate] [-obo byte order] [-oswap] [-ostype sample type] [-scale factor] [-scaleN factor] [-lpfilter frequency] [-hpfilter frequency] [-forder order] [-fafter] [-info] [-add] [-pc LONGEST | FIRST] [-key keylab file] [-divide] [-ext file extension] [-extract file] input files ...

DESCRIPTION

ch_wave performs various operations on an input waveform file and writes it out to another file. Among other things, it can extract subsections or individual channels, resample, rescale, mix down channels, and perform simple filtering operations.

The following option flags are recognized:

Options help
file type
Input file type (optional). If set to raw, this indicates that the input file does not have a header. While this can be used to specify file types other than raw, this is rarely used for other purposes as the file type of all the existing supported types can be determined automatically from the file's header. If the input file is unheadered, files are assumed to be shorts (16bit). Supported types are nist, est, esps, snd, riff, aiff, audlab, raw, ascii
channels Number of channels in an unheadered input file
 
sample rate
Sample rate in Hertz for an unheadered input file
byte order
Input byte order in an unheadered input file: possibliities are: MSB , LSB, native or nonnative. Suns, HP, SGI Mips, M68000 are MSB (big endian) Intel, Alpha, DEC Mips, Vax are LSB (little endian)
Swap bytes. (For use on an unheadered input file)
sample type
Sample type in an unheadered input file: short, alaw, mulaw, byte, ascii
channel
Select a single channel (starts from 0). Waveforms can have multiple channels. This option extracts a single channel for progcessing and discards the rest.
seconds
Extract sub-wave starting at this time, specified in seconds
seconds
Extract sub-wave ending at this time, specified in seconds
sample
Extract sub-wave starting at this sample point
sample
Extract sub-wave ending at this sample point
output file
Output filename. If not specified output is to stdout.
file type
Output file type, (optional). If no type is Specified the type of the input file is assumed. Supported types are: nist, est, esps, snd, riff, aiff, audlab, raw, ascii
sample rate
Output sample rate in Hz. If this is different from the input sample rate, resampling will occur
byte order
Output byte order: MSB, LSB, native, or nonnative. Suns, HP, SGI Mips, M68000 are MSB (big endian), Intel, Alpha, DEC Mips, Vax are LSB (little endian)
Swap bytes when saving to output
sample type
Output sample type: short, alaw, mulaw, byte or ascii
factor
Scaling factor. Increase or descrease the amplitude of the whole waveform by the factor given (relative to 1.0)
factor Scaling factor with normalization. The waveform is
scaled to its maximum level, after which it is scaled by the factor given (relative to 1.0)
frequency
Low pass filter, with cutoff frequency in Hz Filtering is performed by a FIR filter which is built at run time. The order of the filter can be given by -forder. The default value is 199
frequency
High pass filter, with cutoff frequency in Hz Filtering is performed by a FIR filter which is built at run time. The order of the filter can be given by -forder. The default value is 199.
order
Order of FIR filter used for lpfilter and hpfilter. This must be ODD. Sensible values range from 19 (quick but with a shallow rolloff) to 199 (slow but with a steep rolloff). The default is 199.
Do filtering after other operations such as resampling (default : filter before other operations)
Print information about file and header. This option gives useful information such as file length, sampling rate, number of channels etc No output is produced
A new single channel waveform is created by adding the corresponding sample points of each input waveform
LONGEST | FIRST
Combine input waveforms to form a single multichannel waveform. The argument to this option controls how long the new waveform should be. If the option is LONGEST, the output wave if the length of the longest input wave and shorter waves are padded with zeros at the end. If the option is FIRST, the length of the new waveform is the length of the first file on the command line, and subsequent waves are padded or cut to this length
keylab file
Label file designating subsections, for use with -divide. The KEYLAB file is a label file which specifies where chunks (such as individual sentences) in a waveform begin and end. See section on wave extraction.
Divide a single input waveform into multiple output waveforms. Each output waveform is extracted from the input waveform by using the KEYLAB file, which specifies the start and stop times for each chunk. The output files are named according to the filename in the KEYLAB file, with extension given by -ext. See section on wave extraction
file extension
File extension for divided waveforms
file
Used in conjunction with -key to extract a single section of waveform from the input waveform. The argument is the name of a file given in the file column of the KEYLAB file.

EXAMPLES

BUGS

SEE ALSO

ch_track(1) ch_utt(1) na_record(1) na_play(1)

April 5, 2001 Edinburgh Speech Tools