DRBDADM(8) | System Administration | DRBDADM(8) |
NAME¶
drbdadm - Administration tool for DRBD
SYNOPSIS¶
drbdadm [-d] [-c {file}] [-t {file}] [-s {cmd}] [-m {cmd}] [-S] [-h {host}] [-- {backend-options}] {command} [{all} | {resource[/volume>]...}]
DESCRIPTION¶
Drbdadm is the high level tool of the DRBD program suite. Drbdadm is to drbdsetup and drbdmeta what ifup/ifdown is to ifconfig. Drbdadm reads its configuration file and performs the specified commands by calling the drbdsetup and/or the drbdmeta program.
Drbdadm can operate on whole resources or on individual volumes in a resource. The sub commands: attach, detach, primary, secondary, invalidate, invalidate-remote, outdate, resize, verify, pause-sync, resume-sync, role, csytate, dstate, create-md, show-gi, get-gi, dump-md, wipe-md work on whole resources and on individual volumes.
Resource level only commands are: connect, disconnect, up, down, wait-connect and dump.
OPTIONS¶
-d, --dry-run
-c, --config-file file
-t, --config-to-test file
-s, --drbdsetup file
-m, --drbdmeta file
-S, --stacked
-P, --peer
-- backend-options
COMMANDS¶
attach
detach
Removes the backing storage device from a DRBD resource's device.
connect
Sets up the network configuration of the resource's device. If the peer device is already configured, the two DRBD devices will connect. If there are more than two host sections in the resource you need to use the --peer option to select the peer you want to connect to.
disconnect
Removes the network configuration from the resource. The device will then go into StandAlone state.
syncer
Loads the resynchronization parameters into the device.
up
Is a shortcut for attach and connect.
down
Is a shortcut for disconnect and detach.
primary
Promote the resource's device into primary role. You need to do this before any access to the device, such as creating or mounting a file system.
secondary
Brings the device back into secondary role. This is needed since in a connected DRBD device pair, only one of the two peers may have primary role (except if allow-two-primaries is explicitly set in the configuration file).
invalidate
Forces DRBD to consider the data on the local backing storage device as out-of-sync. Therefore DRBD will copy each and every block from its peer, to bring the local storage device back in sync. To avoid races, you need an established replication link, or be disconnected Secondary.
invalidate-remote
This command is similar to the invalidate command, however, the peer's backing storage is invalidated and hence rewritten with the data of the local node. To avoid races, you need an established replication link, or be disconnected Primary.
resize
Causes DRBD to re-examine all sizing constraints, and resize the resource's device accordingly. For example, if you increased the size of your backing storage devices (on both nodes, of course), then DRBD will adopt the new size after you called this command on one of your nodes. Since new storage space must be synchronised this command only works if there is at least one primary node present.
Note that all of the following options are backend-options (i.e., separated via "--").
The --size option can be used to online shrink the usable size of a drbd device. It's the users responsibility to make sure that a file system on the device is not truncated by that operation. Example:
# drbdadm -- --size=10G resize r0
The --assume-peer-has-space allows you to resize a device which is currently not connected to the peer. Use with care, since if you do not resize the peer's disk as well, further connect attempts of the two will fail.
The --assume-clean allows you to resize an existing device and avoid syncing the new space. This is useful when adding addtional blank storage to your device. Example:
# drbdadm -- --assume-clean resize r0
The options --al-stripes and --al-stripe-size-kB may be used to change the layout of the activity log online. In case of internal meta data this may invovle shrinking the user visible size at the same time (unsing the --size) or increasing the avalable space on the backing devices.
check-resize
Calls drbdmeta to eventually move internal meta data. If the backing device was resized, while DRBD was not running, meta data has to be moved to the end of the device, so that the next attach command can succeed.
create-md
Initializes the meta data storage. This needs to be done before a DRBD resource can be taken online for the first time. In case of issues with that command have a look at drbdmeta(8)
get-gi
Shows a short textual representation of the data generation identifiers.
show-gi
Prints a textual representation of the data generation identifiers including explanatory information.
dump-md
Dumps the whole contents of the meta data storage, including the stored bit-map and activity-log, in a textual representation.
outdate
Sets the outdated flag in the meta data.
adjust
Synchronizes the configuration of the device with your configuration file. You should always examine the output of the dry-run mode before actually executing this command.
wait-connect
Waits until the device is connected to its peer device.
role
Shows the current roles of the devices (local/peer). E.g. Primary/Secondary
state
Deprecated alias for "role", see above.
cstate
Shows the current connection state of the devices.
dump
Just parse the configuration file and dump it to stdout. May be used to check the configuration file for syntactic correctness.
outdate
Used to mark the node's data as outdated. Usually used by the peer's fence-peer handler.
verify
Starts online verify. During online verify, data on both nodes is compared for equality. See /proc/drbd for online verify progress. If out-of-sync blocks are found, they are not resynchronized automatically. To do that, disconnect and connect the resource when verification has completed.
See also the notes on data integrity on the drbd.conf manpage.
pause-sync
Temporarily suspend an ongoing resynchronization by setting the local pause flag. Resync only progresses if neither the local nor the remote pause flag is set. It might be desirable to postpone DRBD's resynchronization until after any resynchronization of the backing storage's RAID setup.
resume-sync
Unset the local sync pause flag.
new-current-uuid
Generates a new currend UUID and rotates all other UUID values.
This can be used to shorten the initial resync of a cluster. See the drbdsetup manpage for a more details.
dstate
Show the current state of the backing storage devices. (local/peer)
hidden-commands
VERSION¶
This document was revised for version 8.4.0 of the DRBD distribution.
AUTHOR¶
Written by Philipp Reisner <philipp.reisner@linbit.com> and Lars Ellenberg <lars.ellenberg@linbit.com>
REPORTING BUGS¶
Report bugs to <drbd-user@lists.linbit.com>.
COPYRIGHT¶
Copyright 2001-2011 LINBIT Information Technologies, Philipp Reisner, Lars Ellenberg. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO¶
drbd.conf(5), drbd(8), drbddisk(8), drbdsetup(8), drbdmeta(8) and the DRBD project web site[1]
NOTES¶
- 1.
- DRBD project web site
6 May 2011 | DRBD 8.4.0 |